Vehicle
Wiring Details for your
2009-2011 Nissan Murano Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2009-2011 Nissan Murano . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
WHITE (+) |
@ BCM, (BLACK, 3-PIN PLUG), PIN 1, NOTE #2 |
| STARTER |
BROWN (-) |
@ PUSH-BUTTON IGNITION Switch or BCM, (BLACK, 40-PIN PLUG), PIN 18, NOTE #2 |
| STARTER
2 |
RED (-) |
@ BCM, (GRAY, 40-PIN PLUG), PIN 21, NOTE #2 |
| IGNITION
1 |
BROWN (+) |
@ BCM, (BLACK, 40-PIN PLUG), PIN 11, NOTE #2 |
| IGNITION
2 |
BLUE (-) |
@ BCM, (GRAY, 40-PIN PLUG), PIN 16, NOTE #2 |
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
YELLOW (+) |
@ BCM, (BLACK, 40-PIN PLUG), PIN 31, NOTE #2 |
| ACCESSORY/HEATER
BLOWER 2 |
BLUE (+) |
@ BCM, (BLACK, 40-PIN PLUG), PIN 24, NOTE #2 |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
N/A |
|
| PARKING
LIGHTS ( + ) |
RED (+) |
@ DASH FUSE BOX, (WHITE, 10-PIN PLUG), PIN 8 |
| POWER LOCK |
BLUE (TYPE B), NOTE #3 |
@ POWER WINDOW Main Switch, (WHITE, 16-PIN PLUG), PIN 4 |
| POWER UNLOCK |
RED (TYPE B), Requires Double Pulse, NOTE #4 |
@ POWER WINDOW Main Switch, (WHITE, 16-PIN PLUG), PIN 6 |
| DOOR TRIGGER |
LT. BLUE (-) |
in DRIVERS KICK PANEL or BCM, (GREEN, 40-PIN PLUG), PIN 39, NOTE #2 |
| DOMELIGHT
SUPERVISION |
YELLOW (-) |
in DRIVERS KICK PANEL or BCM, (WHITE, 16-PIN PLUG), PIN 16, NOTE #2 |
| TRUNK RELEASE |
YELLOW to LT. GREEN (-) NOTE #5 and #6 |
in DRIVERS KICK PANEL or BCM, (GRAY, 40-PIN PLUG), PIN 36, NOTE #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
YELLOW (-) |
@ HORN Switch (GRAY, 8-PIN PLUG), PIN 8 |
| TACH |
Any wire NOT LT. GREEN or YELLOW/GREEN (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
LT. GREEN to BLUE (+) |
@ BRAKE Switch or BCM, (GREEN, 40-PIN PLUG), PIN 7, NOTE #2 |
| FACTORY
ALARM DISARM |
Use UNLOCK wire |
|
| ANTI-THEFT |
NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is Equipped with NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM,
for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an
Extra Ignition key. (Requires extra key for Operation)
Part # XK09 for REMOTE STARTING ONLY, requires 1 key for
programming, NO key required for Operation.
Part # DB-ALL for REMOTE START/KEYLESS Entry, requires 1 key for programming
and NO Key for Operation.
To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: the BCM (Body Control Module) is located behind the INSTRUMENT CLUSTER.
NOTE #3: TEST this wire while Turning the KEY in the Drivers Door. This wire will also ARM the
FACTORY ALARM.
NOTE #4: TEST this wire while Turning the KEY in the Drivers Door. This wire will also DISARM the
FACTORY ALARM.
NOTE #5: TEST this wire while opening the Hatch with the Handle on the REAR of the Vehicle.
NOTE #6: On vehicles with the POWER BACK DOOR, the OPEN/CLOSE wire is a YELLOW (-) @ the
POWER BACK DOOR Switch (GRAY, 8-PIN PLUG), PIN 2 or in the DRIVERS KICK PANEL,
Harness to REAR of Vehicle.
|
|
|
|
|
|
