Nissan Murano 2009-2011 Printer Friendly Wiring Chart

Nissan Murano 2009-2011

PART	COLOR	LOCATION
12 VOLT CONSTANT	WHITE (+)	@ BCM, (BLACK, 3-PIN PLUG), PIN 1, NOTE #2
STARTER	BROWN (-)	@ PUSH-BUTTON IGNITION Switch or BCM, (BLACK, 40-PIN PLUG), PIN 18, NOTE #2
STARTER 2	RED (-)	@ BCM, (GRAY, 40-PIN PLUG), PIN 21, NOTE #2
IGNITION 1	BROWN (+)	@ BCM, (BLACK, 40-PIN PLUG), PIN 11, NOTE #2
IGNITION 2	BLUE (-)	@ BCM, (GRAY, 40-PIN PLUG), PIN 16, NOTE #2
IGNITION 3	N/A
ACCESSORY/HEATER BLOWER 1	YELLOW (+)	@ BCM, (BLACK, 40-PIN PLUG), PIN 31, NOTE #2
ACCESSORY/HEATER BLOWER 2	BLUE (+)	@ BCM, (BLACK, 40-PIN PLUG), PIN 24, NOTE #2
KEYSENSE	N/A
PARKING LIGHTS ( - )	N/A
PARKING LIGHTS ( + )	RED (+)	@ DASH FUSE BOX, (WHITE, 10-PIN PLUG), PIN 8
POWER LOCK	BLUE (TYPE B), NOTE #3	@ POWER WINDOW Main Switch, (WHITE, 16-PIN PLUG), PIN 4
POWER UNLOCK	RED (TYPE B), Requires Double Pulse, NOTE #4	@ POWER WINDOW Main Switch, (WHITE, 16-PIN PLUG), PIN 6
DOOR TRIGGER	LT. BLUE (-)	in DRIVERS KICK PANEL or BCM, (GREEN, 40-PIN PLUG), PIN 39, NOTE #2
DOMELIGHT SUPERVISION	YELLOW (-)	in DRIVERS KICK PANEL or BCM, (WHITE, 16-PIN PLUG), PIN 16, NOTE #2
TRUNK RELEASE	YELLOW to LT. GREEN (-) NOTE #5 and #6	in DRIVERS KICK PANEL or BCM, (GRAY, 40-PIN PLUG), PIN 36, NOTE #2
SLIDING POWER DOOR	N/A
HORN	YELLOW (-)	@ HORN Switch (GRAY, 8-PIN PLUG), PIN 8
TACH	Any wire NOT LT. GREEN or YELLOW/GREEN (AC)	@ Any FUEL-INJECTOR
WAIT TO START LIGHT	N/A
BRAKE	LT. GREEN to BLUE (+)	@ BRAKE Switch or BCM, (GREEN, 40-PIN PLUG), PIN 7, NOTE #2
FACTORY ALARM DISARM	Use UNLOCK wire
ANTI-THEFT	NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1

EXTRA INFORMATION

NOTE #1: This vehicle is Equipped with NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM, for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an Extra Ignition key. (Requires extra key for Operation) Part # XK09 for REMOTE STARTING ONLY, requires 1 key for programming, NO key required for Operation. Part # DB-ALL for REMOTE START/KEYLESS Entry, requires 1 key for programming and NO Key for Operation. To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS MODULE Page on this website. NOTE #2: the BCM (Body Control Module) is located behind the INSTRUMENT CLUSTER. NOTE #3: TEST this wire while Turning the KEY in the Drivers Door. This wire will also ARM the FACTORY ALARM. NOTE #4: TEST this wire while Turning the KEY in the Drivers Door. This wire will also DISARM the FACTORY ALARM. NOTE #5: TEST this wire while opening the Hatch with the Handle on the REAR of the Vehicle. NOTE #6: On vehicles with the POWER BACK DOOR, the OPEN/CLOSE wire is a YELLOW (-) @ the POWER BACK DOOR Switch (GRAY, 8-PIN PLUG), PIN 2 or in the DRIVERS KICK PANEL, Harness to REAR of Vehicle.