Vehicle
Wiring Details for your
2009-2011 Mazda Mazda 3 Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2009-2011 Mazda Mazda 3 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
ORANGE (+) |
@ IGNITION SWITCH, (8-PIN PLUG), PIN H |
| STARTER |
LT. GREEN (+), NOTE #6 |
@ IGNITION SWITCH, (8-PIN PLUG), PIN B |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
BLUE (+), NOTE #7 |
@ IGNITION SWITCH, (8-PIN PLUG), PIN A |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
WHITE (+), NOTE #8 |
@ IGNITION SWITCH, (8-PIN PLUG), PIN D |
| ACCESSORY/HEATER
BLOWER 2 |
PINK (+), NOTE #9 |
@ IGNITION SWITCH, (8-PIN PLUG), PIN F |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
GRAY (-) |
@ HEADLIGHT SWITCH or BCM, (BLUE, 24-PIN PLUG(B), PIN V, NOTE #2 |
| PARKING
LIGHTS ( + ) |
ORANGE (+) |
in DRIVERS KICK PANEL, Harness to REAR of Vehicle |
| POWER LOCK |
LT. GREEN (TYPE B) (-) Negative, NOTE #3 |
in DRIVERS KICK PANEL or BCM, (BLUE, 24-PIN PLUG(F), PIN D, NOTE #2 |
| POWER UNLOCK |
Use LOCK wire, See NOTE #4 |
|
| DOOR TRIGGER |
BLUE (-) N.C. |
@ BCM, (BLUE, 24-PIN PLUG(F), PIN G, NOTE #2 |
| DOMELIGHT
SUPERVISION |
GREEN (-) |
in DRIVERS KICK PANEL or BCM, (BLUE, 16-PIN PLUG(E), PIN N, NOTE #2 |
| TRUNK RELEASE |
BROWN (-) NOTE #5 |
in DRIVERS KICK PANEL or BCM, (BLUE, 24-PIN PLUG(F), PIN O, NOTE #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
BLUE (-) |
@ HORN SWITCH or BCM, (BLUE, 24-PIN PLUG(B), PIN U, NOTE #2 |
| TACH |
BLACK/WHITE, BLACK/YELLOW, BLACK/BLUE or BLACK/ORANGE (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
GREEN to PURPLE (+) |
@ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle |
| FACTORY
ALARM DISARM |
Disarms with Interface module |
|
| ANTI-THEFT |
MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is with MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM,
for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an
Extra Ignition key. (Requires extra key for Operation)
Part # PK-ALL or PKFM for REMOTE STARTING ONLY, requires 2 keys for
programming, NO key required for Operation.
Part # DB-ALL for Remote Starting and Keyless Entry operation (no resistors
required), 2 keys required for programming, no key required for Operation.
To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: the BCM, (Body Control Module) is located UNDER the DRIVERS DASH, above the
DRIVERS KICK PANEL.
NOTE #3: This Vehicle requires the INTERFACE BYPASS MODULE DB-ALL for KEYLESS ENTRY
OPERATION
NOTE #4: this Vehicle requires the INTERFACE BYPASS MODULE DB-ALL for KEYLESS ENTRY
Operation
NOTE #5: TEST this wire while Opening the Trunk/Liftgate from the Release Button on the
REAR of the Vehicle.
NOTE #6: On vehicles with the PUSH-BUTTON Start, the START 1 and 2 wires are LT. GREEN (-)
and PURPLE (-) at the ENGINE START/STOP Switch, (12-PIN PLUG), PINS A and B
NOTE #7: On vehicles with the PUSH-BUTTON Start, this wire is located at the RELAY BLOCK,
(6-PIN PLUG), PIN B. The RELAY BLOCK is located under the DRIVERS DASH and to
the LEFT of the Steering Column.
NOTE #8: On vehicles with the PUSH-BUTTON Start, this wire is located at the RELAY BLOCK,
(6-PIN PLUG), PIN F. The RELAY BLOCK is located under the DRIVERS DASH and to
the LEFT of the Steering Column.
NOTE #9: On vehicles with the PUSH-BUTTON Start, this wire is located at the RELAY BLOCK,
(8-PIN PLUG), PIN B. The RELAY BLOCK is located under the DRIVERS DASH and to
the LEFT of the Steering Column.
|
|
|
|
|
|
