Vehicle
Wiring Details for your
2009-2011 Mazda Cx-9 Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2009-2011 Mazda Cx-9 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
RED (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN F |
| STARTER |
BLACK/BLUE (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN A |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
BLUE (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN C |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
BLACK/RED (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN B |
| ACCESSORY/HEATER
BLOWER 2 |
BLACK/WHITE (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN D |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BROWN or BROWN/WHITE (-) |
@ HEADLIGHT SWITCH, (17-PIN PLUG), PIN L |
| PARKING
LIGHTS ( + ) |
LT. GREEN (+) |
@ BCM, (24-PIN PLUG(6), PIN D, NOTE #2 |
| POWER LOCK |
PURPLE/WHITE (TYPE B) (-) Negative |
@ BCM, (30-PIN PLUG(3), PIN R, NOTE #2 |
| POWER UNLOCK |
Use LOCK wire, See NOTE #3 |
|
| DOOR TRIGGER |
GRAY/RED (-) |
@ BCM, (24-PIN PLUG(6), PIN O, NOTE #2 |
| DOMELIGHT
SUPERVISION |
YELLOW/RED (-) |
@ BCM, (8-PIN PLUG(7), PIN I, NOTE #2 |
| TRUNK RELEASE |
WHITE/GREEN and WHITE/BLACK, NOTE #4 |
@ POWER LIFTGATE Switch, (6-PIN PLUG), PINS A and C |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
GREEN/RED (-) |
@ BCM, (30-PIN PLUG(3), PIN U, NOTE #2 |
| TACH |
Any wire NOT BLUE (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
GREEN/YELLOW (+) |
@ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle |
| FACTORY
ALARM DISARM |
Disarms with Interface Bypass Module |
|
| ANTI-THEFT |
MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is with MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM,
for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an
Extra Ignition key. (Requires extra key for Operation)
Part # PK-ALL or PKFM for REMOTE STARTING ONLY, requires 2 keys for
programming, NO key required for Operation.
Part # DB-ALL for Remote Starting and Keyless Entry operation (no resistors
required), 2 keys required for programming, no key required for Operation.
To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: the BCM, (Body Control Module) is located in the DRIVERS KICK PANEL.
NOTE #3: to connect KEYLESS ENTRY in this vehicle will require the DB-ALL Interface Bypass
Module, to order go to the Interface bypass module page on this website
NOTE #4: Use a RELAY to SHORT these 2 wires together to Open/Close the Power Liftgate
|
|
|
|
|
|
