Vehicle
Wiring Details for your
2009-2011 Lexus Es350 Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2009-2011 Lexus Es350 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
WHITE (+) |
@ DASH FUSE BOX, (WHITE, 1-PIN PLUG(A) PIN 1 |
| STARTER |
BLUE (-) |
@ ENGINE SWITCH, (BLACK, 14-PIN PLUG) PIN 7 |
| STARTER
2 |
PURPLE (-) |
@ ENGINE SWITCH, (BLACK, 14-PIN PLUG) PIN 2 |
| IGNITION
1 |
BLACK (+) |
@ DASH FUSE BOX, (REAR, WHITE, 10-PIN PLUG(I) PIN 1 |
| IGNITION
2 |
LT. GREEN (+) |
@ DASH FUSE BOX, (REAR, WHITE, 10-PIN PLUG(I) PIN 9 |
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
LT. GREEN (+) |
@ DASH FUSE BOX, (REAR, WHITE, 10-PIN PLUG(I) PIN 3 |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BLACK (-) |
@ HEADLIGHT SWITCH, (WHITE, 20-PIN PLUG) PIN 18 |
| PARKING
LIGHTS ( + ) |
N/A |
|
| POWER LOCK |
RED (TYPE B), (TEST with PASSENGER Switch) NOTE #2 |
@ DASH FUSE BOX, (WHITE, 12-PIN PLUG(J) PIN 3 |
| POWER UNLOCK |
GREEN (TYPE B), (TEST with PASSENGER Switch) NOTE #3 |
@ DASH FUSE BOX, (WHITE, 12-PIN PLUG(J) PIN 4 |
| DOOR TRIGGER |
GRAY (-) |
in DRIVERS KICK PANEL, (BLUE, 20-PIN PLUG) PIN 13 |
| DOMELIGHT
SUPERVISION |
BROWN (-) |
@ DASH FUSE BOX, (WHITE, 12-PIN PLUG(R) PIN 5 |
| TRUNK RELEASE |
PURPLE (-) |
@ RELEASE SWITCH, (BLACK, 6-PIN PLUG) PIN 6 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
GRAY to BLACK (-) |
@ HORN SWITCH or DASH FUSE BOX, (WHITE, 16-PIN PLUG(D) PIN 11 |
| TACH |
BLACK (AC) |
@ BECU, (WHITE, 16-PIN PLUG) PIN 8, NOTE #5 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
BLUE or WHITE (+) |
@ BRAKE SWITCH or DASH FUSE BOX, (WHITE, 14-PIN PLUG(c) PIN 13 |
| FACTORY
ALARM DISARM |
PURPLE (-) Requires Double Pulse, NOTE #4 |
in DRIVERS KICK PANEL, (GRAY, 25-PIN PLUG) PIN 8 |
| ANTI-THEFT |
TOYOTA'S TRANSPONDER SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: LEXUS TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module,
Part # 791 Bypass Module (for REMOTE STARTING ONLY!) an Extra Ignition key is
required to be placed inside this module for Operation.
Part # PK-ALL Bypass Module (for REMOTE STARTING ONLY!) KEYLESS BYPASS
NO KEY is required for Operation.
Part # DB-ALL Bypass Module, this Module is a KEYLESS BYPASS MODULE and DOES
NOT require a Key to be placed inside the Module for Operation, this module will also
do the Keyless Entry.
To order the Bypass Module go to the INTERFACE BYPASS MODULE Page on this
website
NOTE #2: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Arm wire.
NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Disarm wire.
NOTE #4: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock
the Doors.
NOTE #5: the BECU, (Body Electronic Control Unit) is located under the Drivers Dash, attached
to the BACK of the DASH FUSE BOX.
|
|
|
|
|
|
