Lexus Es350 2009-2011 Printer Friendly Wiring Chart

Lexus Es350 2009-2011

PART	COLOR	LOCATION
12 VOLT CONSTANT	WHITE (+)	@ DASH FUSE BOX, (WHITE, 1-PIN PLUG(A) PIN 1
STARTER	BLUE (-)	@ ENGINE SWITCH, (BLACK, 14-PIN PLUG) PIN 7
STARTER 2	PURPLE (-)	@ ENGINE SWITCH, (BLACK, 14-PIN PLUG) PIN 2
IGNITION 1	BLACK (+)	@ DASH FUSE BOX, (REAR, WHITE, 10-PIN PLUG(I) PIN 1
IGNITION 2	LT. GREEN (+)	@ DASH FUSE BOX, (REAR, WHITE, 10-PIN PLUG(I) PIN 9
IGNITION 3	N/A
ACCESSORY/HEATER BLOWER 1	LT. GREEN (+)	@ DASH FUSE BOX, (REAR, WHITE, 10-PIN PLUG(I) PIN 3
ACCESSORY/HEATER BLOWER 2	N/A
KEYSENSE	N/A
PARKING LIGHTS ( - )	BLACK (-)	@ HEADLIGHT SWITCH, (WHITE, 20-PIN PLUG) PIN 18
PARKING LIGHTS ( + )	N/A
POWER LOCK	RED (TYPE B), (TEST with PASSENGER Switch) NOTE #2	@ DASH FUSE BOX, (WHITE, 12-PIN PLUG(J) PIN 3
POWER UNLOCK	GREEN (TYPE B), (TEST with PASSENGER Switch) NOTE #3	@ DASH FUSE BOX, (WHITE, 12-PIN PLUG(J) PIN 4
DOOR TRIGGER	GRAY (-)	in DRIVERS KICK PANEL, (BLUE, 20-PIN PLUG) PIN 13
DOMELIGHT SUPERVISION	BROWN (-)	@ DASH FUSE BOX, (WHITE, 12-PIN PLUG(R) PIN 5
TRUNK RELEASE	PURPLE (-)	@ RELEASE SWITCH, (BLACK, 6-PIN PLUG) PIN 6
SLIDING POWER DOOR	N/A
HORN	GRAY to BLACK (-)	@ HORN SWITCH or DASH FUSE BOX, (WHITE, 16-PIN PLUG(D) PIN 11
TACH	BLACK (AC)	@ BECU, (WHITE, 16-PIN PLUG) PIN 8, NOTE #5
WAIT TO START LIGHT	N/A
BRAKE	BLUE or WHITE (+)	@ BRAKE SWITCH or DASH FUSE BOX, (WHITE, 14-PIN PLUG(c) PIN 13
FACTORY ALARM DISARM	PURPLE (-) Requires Double Pulse, NOTE #4	in DRIVERS KICK PANEL, (GRAY, 25-PIN PLUG) PIN 8
ANTI-THEFT	TOYOTA'S TRANSPONDER SYSTEM, See NOTE #1

EXTRA INFORMATION

NOTE #1: LEXUS TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, Part # 791 Bypass Module (for REMOTE STARTING ONLY!) an Extra Ignition key is required to be placed inside this module for Operation. Part # PK-ALL Bypass Module (for REMOTE STARTING ONLY!) KEYLESS BYPASS NO KEY is required for Operation. Part # DB-ALL Bypass Module, this Module is a KEYLESS BYPASS MODULE and DOES NOT require a Key to be placed inside the Module for Operation, this module will also do the Keyless Entry. To order the Bypass Module go to the INTERFACE BYPASS MODULE Page on this website NOTE #2: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Arm wire. NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Disarm wire. NOTE #4: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock the Doors. NOTE #5: the BECU, (Body Electronic Control Unit) is located under the Drivers Dash, attached to the BACK of the DASH FUSE BOX.