Vehicle
Wiring Details for your
2009-2011 Infiniti Fx35 Wiring Diagram |
Printer Friendly Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2009-2011 Infiniti Fx35 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
|
PART |
COLOR |
LOCATION |
12 VOLT
CONSTANT |
WHITE (+) |
@ BCM, (BLACK, 3-PIN PLUG), PIN 1, NOTE #2 |
STARTER |
LT. BLUE (-) |
@ PUSH-BUTTON IGNITION Switch or BCM, (BLACK, 40-PIN PLUG), PIN 18, NOTE #2 |
STARTER
2 |
LT. GREEN (-) |
@ BCM, (GRAY, 40-PIN PLUG), PIN 21, NOTE #2 |
IGNITION
1 |
PINK (+) |
@ BCM, (BLACK, 40-PIN PLUG), PIN 1, NOTE #2 |
IGNITION
2 |
YELLOW (-) |
@ BCM, (GRAY, 40-PIN PLUG), PIN 16, NOTE #2 |
IGNITION
3 |
N/A |
|
ACCESSORY/HEATER
BLOWER 1 |
ORANGE (+) |
@ BCM, (BLACK, 40-PIN PLUG), PIN 31, NOTE #2 |
ACCESSORY/HEATER
BLOWER 2 |
ORANGE (+) |
@ BCM, (BLACK, 40-PIN PLUG), PIN 24, NOTE #2 |
KEYSENSE |
N/A |
|
PARKING
LIGHTS ( - ) |
N/A |
|
PARKING
LIGHTS ( + ) |
RED (+) |
@ FUSE BOX, (WHITE, 10-PIN PLUG), PIN 8 |
POWER LOCK |
PURPLE (TYPE B), See NOTE #3 |
@ POWER WINDOW Main Switch,(WHITE, 16-PIN PLUG), PIN 4 |
POWER UNLOCK |
YELLOW (TYPE B), Requires Double Pulse, See NOTE #4 |
@ POWER WINDOW Main Switch,(WHITE, 16-PIN PLUG), PIN 6 |
DOOR TRIGGER |
GRAY (-) |
@ BCM, (GREEN, 40-PIN PLUG), PIN 39, NOTE #2 |
DOMELIGHT
SUPERVISION |
LT. BLUE (-) |
@ BCM, (WHITE, 16-PIN PLUG), PIN 16, NOTE #2 |
TRUNK RELEASE |
PINK (-), NOTE #5 |
@ BCM, (GRAY, 40-PIN PLUG), PIN 36, NOTE #2 |
SLIDING
POWER DOOR |
N/A |
|
HORN |
GREEN (-) |
@ HORN Switch, (GRAY, 8-PIN PLUG), PIN 8 |
TACH |
RED (AC) |
@ ECM, (GRAY, 32-PIN PLUG), PIN 14(V6) or PIN 1(V8), NOTE #6 |
WAIT TO
START LIGHT |
N/A |
|
BRAKE |
PINK (+) |
@ BCM, (GREEN, 40-PIN PLUG), PIN 7, NOTE #2 |
FACTORY
ALARM DISARM |
Use UNLOCK wire |
|
ANTI-THEFT |
INFINITI'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, See NOTE #1 |
|
EXTRA
INFORMATION |
NOTE #1: NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module,
Part # 791 or XK09 (For REMOTE START ONLY)
Part # DB-ALL (for REMOTE START and DOOR LOCKS)
to order the INTERFACE BYPASS MODULES go to the Interface Bypass Module page
on this website.
NOTE #2: the BCM (Body Control Module) is located in the PASSENGER KICK PANEL.
NOTE #3: TEST this wire while Turning the KEY in the Drivers Door. This wire will also ARM the
FACTORY ALARM.
NOTE #4: TEST this wire while Turning the KEY in the Drivers Door. This wire will also DISARM the
FACTORY ALARM.
NOTE #5: TEST this wire while opening the Liftgate with the Handle on the REAR of the Vehicle.
NOTE #6: the ECM, (Engine control Module) is located Behind the GLOVE BOX.
|
|
|
|
|