Vehicle
Wiring Details for your
2009-2011 Honda Pilot Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2009-2011 Honda Pilot . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
WHITE (+) |
@ IGNITION SWITCH, (WHITE, 5-Pin Plug) Pin 2 |
| STARTER |
YELLOW (+) |
@ IGNITION SWITCH, (WHITE, 5-Pin Plug) Pin 1 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
PINK (+) |
@ IGNITION SWITCH, (WHITE, 5-Pin Plug) Pin 5 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
ORANGE (+) |
@ IGNITION SWITCH, (WHITE, 5-Pin Plug) Pin 3 |
| ACCESSORY/HEATER
BLOWER 2 |
RED (+) |
@ IGNITION SWITCH, (WHITE, 5-Pin Plug) Pin 4 |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
GRAY (-) (REQUIRES #775 RELAY) |
@ HEADLIGHT SWITCH, (BLACK/WHITE, 12-Pin Plug) Pin 11 |
| PARKING
LIGHTS ( + ) |
GRAY (+) |
@ DASH FUSE BOX, (LT. GREEN, 42-Pin Plug) Pin 19 |
| POWER LOCK |
PINK (TYPE B), See NOTE #2 |
@ POWER WINDOW Master Switch, (GRAY, 37-Pin Plug) Pin 28 |
| POWER UNLOCK |
WHITE (-) and RED (-) TYPE B, (DOUBLE PULSE Required), See NOTE #2 |
@ POWER WINDOW Master Switch, (GRAY, 37-Pin Plug) Pins 29 and 31 |
| DOOR TRIGGER |
YELLOW (-) |
@ DASH FUSE BOX, (LT. GREEN, 42-Pin Plug) Pin 37 |
| DOMELIGHT
SUPERVISION |
PINK (-) |
Above DRIVERS KICK PANEL, (GRAY, 2-Pin Plug) Pin 1 |
| TRUNK RELEASE |
ORANGE (-) (Liftgate) NOTE #3 and #4 |
@ DASH FUSE BOX, (LT. GREEN, 42-Pin Plug) Pin 13 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
GRAY (-) |
@ HORN SWITCH, (WHITE, 20-Pin Plug) Pin 1 |
| TACH |
Any wire NOT YELLOW/BLACK (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
LIGHT BLUE (+) |
@ BRAKE SWITCH or DASH FUSE BOX, (LT. GREEN, 42-Pin Plug) Pin 34 |
| FACTORY
ALARM DISARM |
DISARMS with UNLOCK |
|
| ANTI-THEFT |
HONDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: HONDA'S TRANSPONDER SYSTEM, Requires Bypass Module:
(For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation.
(For Remote Starting Only) Part # PK-ALL Bypass. (No Extra Key Required for
Operation) 2-KEYS Required to Program Module.
(For Remote Starting/Door Locks) Part # DB-ALL (No Extra Key Required for Operation)
1-KEY Required for Programming.
To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: METER THE DOORLOCK WIRES WHILE TURNING THE KEY IN THE DRIVERS DOOR
CYLINDER. WHITE IS THE DRIVER DOOR KEY CYLINDER, WHITE IS THE UNLOCK WIRE
AND THE RED IS THE DOOR UNLOCK DETECTION WIRE. USE BOTH WIRES AND DIODE
ISOLATE EACH.
NOTE #3: THE HATCH GLASS RELEASE WIRE, IS A PINK (-) LOCATED IN THE DRIVERS KICK
PANEL, AT A WHITE, 18-PIN PLUG, PIN 8. TEST THESE WIRES WHILE OPENING THE
LIFTGATE/HATCH GLASS FROM THE HANDLE ON THE REAR OF THE VEHICLE.
NOTE #4: ON VEHICLES WITH POWER TAILGATE, THE OPEN/CLOSE WIRES ARE BROWN
(SWITCH) AND PURPLE to WHITE (COMMON), ABOVE THE DRIVERS KICK PANEL,
IN A WHITE,24-PIN PLUG, PINS 20 AND 9. THESE WIRES SHORT WHEN THE SWITCH
IS PRESSED.
|
|
|
|
|
|
