Vehicle
Wiring Details for your
2008-2011 Toyota Land Cruiser Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2008-2011 Toyota Land Cruiser . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
BLACK (+) |
@ DRIVERS DASH FUSE BOX, (WHITE, 1-Pin Plug(A) Pin 1 |
| STARTER |
SEE NOTE #1 |
|
| STARTER
2 |
N/A |
|
| IGNITION
1 |
SEE NOTE #1 |
|
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
SEE NOTE #1 |
|
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
PURPLE (-) |
@ HEADLIGHT SWITCH or BECU, (WHITE, 26-Pin Plug) Pin 23, NOTE #6 |
| PARKING
LIGHTS ( + ) |
GREEN (+) |
@ DRIVERS DASH FUSE BOX, (WHITE, 24-Pin Plug(C) Pin 22 |
| POWER LOCK |
RED (TYPE B), (TEST with Passenger Switch), NOTE #2 |
@ DRIVERS DASH FUSE BOX, (WHITE, 66-Pin Plug(D) Pin 49 |
| POWER UNLOCK |
GREEN (TYPE B), (TEST with Passenger Switch), NOTE #3 |
@ DRIVERS DASH FUSE BOX, (WHITE, 66-Pin Plug(D) Pin 52 |
| DOOR TRIGGER |
BLUE (-) |
@ BECU, (WHITE, 26-Pin Plug) Pin 24, NOTE #6 |
| DOMELIGHT
SUPERVISION |
GREEN (-) |
@ DRIVERS DASH FUSE BOX, (WHITE, 66-Pin Plug(D) Pin 51 |
| TRUNK RELEASE |
BLUE (-) NOTE #4 |
@ BECU, (WHITE, 26-Pin Plug) Pin 26, NOTE #6 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
GRAY to RED/WHITE (-) |
@ HORN SWITCH or DRIVERS DASH FUSE BOX, (WHITE, 24-Pin Plug(B) Pin 1 |
| TACH |
WHITE (AC) |
@ DATA LINK Connector, (WHITE, 16-Pin Plug) Pin 9 or BECU, (WHITE, 16-Pin Plug) Pin 8, NOTE #6 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
RED (+) |
@ BRAKE SWITCH or DRIVERS DASH FUSE BOX, (WHITE, 24-Pin Plug(B) Pin 22 |
| FACTORY
ALARM DISARM |
YELLOW (-) (Requires Double Pulse), NOTE #7 |
@ BECU, (WHITE, 26-Pin Plug) Pin 10, NOTE #6 |
| ANTI-THEFT |
TOYOTA'S MULTIPLEX IGNITION/TRANSPONDER SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This vehicle has a MULTIPLEX IGNITION CIRCUIT/ANTI-THEFT SYSTEM that Requires
a Special INTERFACE BYPASS MODULE Part # DB-ALL to REMOTE START, to order
please go to the INTERFACE BYPASS MODULE Page on this website.
NOTE #2: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Arm wire.
NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Disarm wire.
NOTE #4: TEST this wire while opening the Liftgate from the Handle on the Rear of the
Vehicle.
NOTE #5: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock
the Doors.
NOTE #6: the BECU is located under the Driver Dash, attached to the Fuse Box.
NOTE #7: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock
the Doors.
|
|
|
|
|
|
