Vehicle
Wiring Details for your
2008-2010 Toyota Sienna Wiring Diagram |
Printer Friendly Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2008-2010 Toyota Sienna . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
|
PART |
COLOR |
LOCATION |
12 VOLT
CONSTANT |
WHITE/RED (+) |
@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 5 |
STARTER |
BLACK/YELLOW (+) |
@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 4 |
STARTER
2 |
N/A |
|
IGNITION
1 |
BLACK (+) |
@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 6 |
IGNITION
2 |
BLACK/YELLOW (+) |
@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 2 |
IGNITION
3 |
N/A |
|
ACCESSORY/HEATER
BLOWER 1 |
PINK (+) |
@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 3 |
ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
KEYSENSE |
N/A |
|
PARKING
LIGHTS ( - ) |
GREEN/BLACK (-) |
@ HEADLIGHT Switch, (WHITE, 17-Pin Plug) Pin 14 |
PARKING
LIGHTS ( + ) |
N/A |
|
POWER LOCK |
RED/YELLOW (TYPE B), NOTE #2 |
in DRIVERS KICK PANEL, (WHITE, 12-Pin Plug) Pin 7 |
POWER UNLOCK |
GREEN (TYPE B), NOTE #3 |
in DRIVERS KICK PANEL, (WHITE, 12-Pin Plug) Pin 9 |
DOOR TRIGGER |
RED/YELLOW (-) |
@ DASH JUNCTION BLOCK, (WHITE, 32-Pin Plug(J12) Pin 22 |
DOMELIGHT
SUPERVISION |
BLUE (-) |
@ INTERIOR LIGHT Switch, (WHITE, 10-Pin Plug) Pin 5 |
TRUNK RELEASE |
GREEN/BLACK (-) NOTE #5 |
@ DASH JUNCTION BLOCK, (WHITE, 32-Pin Plug(J14) Pin 7 |
SLIDING
POWER DOOR |
YELLOW/GREEN (-) |
Below DASH JUNCTION BLOCK, (WHITE, 22-Pin Plug) Pin 11 |
HORN |
GREEN/BLACK (-) |
@ DAH FUSE BOX, ((WHITE, 30-Pin Plug(C) Pin 25 |
TACH |
BLACK/ORANGE (AC) |
@ ECM, (WHITE, 35-Pin Plug(E5) Pin 1, NOTE # |
WAIT TO
START LIGHT |
N/A |
|
BRAKE |
GREEN/WHITE (+) |
@ DAH FUSE BOX, ((WHITE, 25-Pin Plug(P) Pin 3 |
FACTORY
ALARM DISARM |
BLUE (-) Requires Double Pulse, NOTE #4 |
in DRIVERS KICK PANEL, (WHITE, 18-Pin Plug) Pin 7 |
ANTI-THEFT |
TRANSPONDER ANTI-THEFT, SEE NOTE #1 |
@ IGNITION SWITCH TUMBLER |
EXTRA
INFORMATION |
NOTE #1: TOYOTA'S TRANSPONDER SYSTEM, Requires Bypass Module:
(For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation.
(For Remote Starting Only) Part # PK-ALL Bypass. (No Extra Key Required for
Operation) 2-KEYS Required to Program Module.
To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Arm wire. Factory Arm wire is Light Green in an (18-pin plug, Pin 5) @ Drivers Kick Panel.
NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Disarm wire.
NOTE #4: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock
the Doors.
NOTE #5: TEST this wire while opening the Liftgate with the Handle on the rear of the Vehicle.
on vehicles with Power Liftgate, the Open/close wire is YELLOW/RED (-) below the
Dash Junction Block, (WHITE, 22-Pin Plug) Pin 10.
NOTE #6: the ECM (Engine Control Module) is located under the Passenger Dash, behind the
Glove Box.
|
|
|
|
|