Toyota Sienna 2008-2010 Printer Friendly Wiring Chart

Toyota Sienna 2008-2010

PART	COLOR	LOCATION
12 VOLT CONSTANT	WHITE/RED (+)	@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 5
STARTER	BLACK/YELLOW (+)	@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 4
STARTER 2	N/A
IGNITION 1	BLACK (+)	@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 6
IGNITION 2	BLACK/YELLOW (+)	@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 2
IGNITION 3	N/A
ACCESSORY/HEATER BLOWER 1	PINK (+)	@ IGNITION SWITCH, (WHITE, 6-Pin Plug) Pin 3
ACCESSORY/HEATER BLOWER 2	N/A
KEYSENSE	N/A
PARKING LIGHTS ( - )	GREEN/BLACK (-)	@ HEADLIGHT Switch, (WHITE, 17-Pin Plug) Pin 14
PARKING LIGHTS ( + )	N/A
POWER LOCK	RED/YELLOW (TYPE B), NOTE #2	in DRIVERS KICK PANEL, (WHITE, 12-Pin Plug) Pin 7
POWER UNLOCK	GREEN (TYPE B), NOTE #3	in DRIVERS KICK PANEL, (WHITE, 12-Pin Plug) Pin 9
DOOR TRIGGER	RED/YELLOW (-)	@ DASH JUNCTION BLOCK, (WHITE, 32-Pin Plug(J12) Pin 22
DOMELIGHT SUPERVISION	BLUE (-)	@ INTERIOR LIGHT Switch, (WHITE, 10-Pin Plug) Pin 5
TRUNK RELEASE	GREEN/BLACK (-) NOTE #5	@ DASH JUNCTION BLOCK, (WHITE, 32-Pin Plug(J14) Pin 7
SLIDING POWER DOOR	YELLOW/GREEN (-)	Below DASH JUNCTION BLOCK, (WHITE, 22-Pin Plug) Pin 11
HORN	GREEN/BLACK (-)	@ DAH FUSE BOX, ((WHITE, 30-Pin Plug(C) Pin 25
TACH	BLACK/ORANGE (AC)	@ ECM, (WHITE, 35-Pin Plug(E5) Pin 1, NOTE #
WAIT TO START LIGHT	N/A
BRAKE	GREEN/WHITE (+)	@ DAH FUSE BOX, ((WHITE, 25-Pin Plug(P) Pin 3
FACTORY ALARM DISARM	BLUE (-) Requires Double Pulse, NOTE #4	in DRIVERS KICK PANEL, (WHITE, 18-Pin Plug) Pin 7
ANTI-THEFT	TRANSPONDER ANTI-THEFT, SEE NOTE #1	@ IGNITION SWITCH TUMBLER

EXTRA INFORMATION

NOTE #1: TOYOTA'S TRANSPONDER SYSTEM, Requires Bypass Module: (For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation. (For Remote Starting Only) Part # PK-ALL Bypass. (No Extra Key Required for Operation) 2-KEYS Required to Program Module. To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS MODULE Page on this website. NOTE #2: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Arm wire. Factory Arm wire is Light Green in an (18-pin plug, Pin 5) @ Drivers Kick Panel. NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Disarm wire. NOTE #4: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock the Doors. NOTE #5: TEST this wire while opening the Liftgate with the Handle on the rear of the Vehicle. on vehicles with Power Liftgate, the Open/close wire is YELLOW/RED (-) below the Dash Junction Block, (WHITE, 22-Pin Plug) Pin 10. NOTE #6: the ECM (Engine Control Module) is located under the Passenger Dash, behind the Glove Box.