Vehicle
Wiring Details for your
2008-2010 Mazda Rx-8 Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2008-2010 Mazda Rx-8 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
GREEN (+) |
@ FUSE BOX, in DRIVERS KICK PANEL |
| STARTER |
WHITE/BLUE (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 1 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
BLUE/BLACK (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 2 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
BLUE/GREEN (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 4 |
| ACCESSORY/HEATER
BLOWER 2 |
WHITE/RED (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 5 |
| KEYSENSE |
PINK/BLACK (+) |
@ IGNITION SWITCH (2-PIN PLUG), PIN 2 OR AT KCM, 24PIN PLUG PIN F |
| PARKING
LIGHTS ( - ) |
LT. GREEN or PINK/BLACK (-) |
@ HEADLIGHT SWITCH, (17-PIN PLUG), PIN L |
| PARKING
LIGHTS ( + ) |
BLACK/RED (+) |
in DRIVERS KICK PANEL, Harness to REAR of Vehicle |
| POWER LOCK |
LT. GREEN (-) thru a 1000 Ohm Resistor, NOTE #3 |
in DRIVERS KICK PANEL or KCM, (24-PIN PLUG), PIN V, NOTE #2 |
| POWER UNLOCK |
Use LOCK wire |
|
| DOOR TRIGGER |
WHITE/RED (-) |
in DRIVERS KICK PANEL, Harness to REAR of Vehicle |
| DOMELIGHT
SUPERVISION |
GREEN/BLACK (-) |
in DRIVERS KICK PANEL or KCM, (6-PIN PLUG(1), PIN B, NOTE #2 |
| TRUNK RELEASE |
YELLOW or WHITE/BLUE to WHITE/BLACK (-) |
@ RELEASE SWITCH or KCM, (24-PIN PLUG(1), PIN E, NOTE #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
GREEN/ORANGE (-) |
@ HORN SWITCH or KCM, (24-PIN PLUG) PIN C, NOTE #2 |
| TACH |
Any wire NOT WHITE/BLUE (AC) |
@ Any FUEL -INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
BLACK/BLUE to BLACK/YELLOW (+) |
@ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle. |
| FACTORY
ALARM DISARM |
GREEN/RED (-) thru a 1000 Ohm Resistor, NOTE #4 |
in DRIVERS KICK PANEL or KCM, (24-PIN PLUG), PIN s, NOTE #2 |
| ANTI-THEFT |
MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is with MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM,
for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an
Extra Ignition key. (Requires extra key for Operation)
Part # PK-ALL or PKFM for REMOTE STARTING ONLY, requires 2 keys for
programming, NO key required for Operation.
Part # DB-ALL for Remote Starting and Keyless Entry operation (no resistors
required), 2 keys required for programming, no key required for Operation.
To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: The KCM (Keyless Control Module) is located behind the GLOVE BOX
NOTE #3: This Vehicle uses a 1-Wire Door Locking System, it Requires (-) thru a 1000 Ohm
Resistor to Lock and a (-) to Unlock.
NOTE #4: this Vehicle uses a 1-Wire ARM/DISARM System, it Requires (-) thru a 1000 Ohm
Resistor to DISARM the Factory Alarm System.
|
|
|
|
|
|
