Mazda  Rx-8 2008-2010
 PART   COLOR  LOCATION
 12 VOLT CONSTANT   GREEN (+)   @ FUSE BOX, in DRIVERS KICK PANEL
 STARTER  WHITE/BLUE (+)  @ IGNITION SWITCH, (6-PIN PLUG), PIN 1
 STARTER 2  N/A  
 IGNITION 1  BLUE/BLACK (+)  @ IGNITION SWITCH, (6-PIN PLUG), PIN 2
 IGNITION 2  N/A  
 IGNITION 3  N/A  
 ACCESSORY/HEATER BLOWER 1  BLUE/GREEN (+)  @ IGNITION SWITCH, (6-PIN PLUG), PIN 4
 ACCESSORY/HEATER BLOWER 2  WHITE/RED (+)  @ IGNITION SWITCH, (6-PIN PLUG), PIN 5
 KEYSENSE  PINK/BLACK (+)  @ IGNITION SWITCH (2-PIN PLUG), PIN 2 OR AT KCM, 24PIN PLUG PIN F
 PARKING LIGHTS ( - )  LT. GREEN or PINK/BLACK (-)  @ HEADLIGHT SWITCH, (17-PIN PLUG), PIN L
 PARKING LIGHTS ( + )  BLACK/RED (+)  in DRIVERS KICK PANEL, Harness to REAR of Vehicle
 POWER LOCK  LT. GREEN (-) thru a 1000 Ohm Resistor, NOTE #3  in DRIVERS KICK PANEL or KCM, (24-PIN PLUG), PIN V, NOTE #2
 POWER UNLOCK  Use LOCK wire  
 DOOR TRIGGER  WHITE/RED (-)  in DRIVERS KICK PANEL, Harness to REAR of Vehicle
 DOMELIGHT SUPERVISION  GREEN/BLACK (-)  in DRIVERS KICK PANEL or KCM, (6-PIN PLUG(1), PIN B, NOTE #2
 TRUNK RELEASE  YELLOW or WHITE/BLUE to WHITE/BLACK (-)  @ RELEASE SWITCH or KCM, (24-PIN PLUG(1), PIN E, NOTE #2
 SLIDING POWER DOOR  N/A  
 HORN  GREEN/ORANGE (-)  @ HORN SWITCH or KCM, (24-PIN PLUG) PIN C, NOTE #2
 TACH  Any wire NOT WHITE/BLUE (AC)  @ Any FUEL -INJECTOR
 WAIT TO START LIGHT  N/A  
 BRAKE  BLACK/BLUE to BLACK/YELLOW (+)  @ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle.
 FACTORY ALARM DISARM   GREEN/RED (-) thru a 1000 Ohm Resistor, NOTE #4  in DRIVERS KICK PANEL or KCM, (24-PIN PLUG), PIN s, NOTE #2
 ANTI-THEFT  MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1  
 EXTRA INFORMATION
 NOTE #1: This vehicle is with MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an Extra Ignition key. (Requires extra key for Operation) Part # PK-ALL or PKFM for REMOTE STARTING ONLY, requires 2 keys for programming, NO key required for Operation. Part # DB-ALL for Remote Starting and Keyless Entry operation (no resistors required), 2 keys required for programming, no key required for Operation. To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS MODULE Page on this website. NOTE #2: The KCM (Keyless Control Module) is located behind the GLOVE BOX NOTE #3: This Vehicle uses a 1-Wire Door Locking System, it Requires (-) thru a 1000 Ohm Resistor to Lock and a (-) to Unlock. NOTE #4: this Vehicle uses a 1-Wire ARM/DISARM System, it Requires (-) thru a 1000 Ohm Resistor to DISARM the Factory Alarm System.