Vehicle
Wiring Details for your
2008-2010 Infiniti Qx56 Wiring Diagram |
Printer Friendly Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2008-2010 Infiniti Qx56 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
|
PART |
COLOR |
LOCATION |
12 VOLT
CONSTANT |
GREEN (+) 40 AMP |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 3 |
STARTER |
BROWN (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 2 |
STARTER
2 |
LT. GREEN (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 6 |
IGNITION
1 |
BLACK/RED (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 1 |
IGNITION
2 |
N/A |
|
IGNITION
3 |
N/A |
|
ACCESSORY/HEATER
BLOWER 1 |
RED (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 4 |
ACCESSORY/HEATER
BLOWER 2 |
PURPLE (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 5 |
KEYSENSE |
N/A |
|
PARKING
LIGHTS ( - ) |
N/A |
|
PARKING
LIGHTS ( + ) |
RED/BLUE (+) |
in EITHER KICK PANEL, Harness to REAR of Vehicle |
POWER LOCK |
BLUE (-), TYPE B, NOTE #3 |
@ POWER WINDOW Main Switch, (WHITE, 16-PIN PLUG), PIN 4 |
POWER UNLOCK |
RED (-), TYPE B, Requires Double Pulse, NOTE #4 |
@ POWER WINDOW Main Switch, (WHITE, 16-PIN PLUG), PIN 6 |
DOOR TRIGGER |
LT. BLUE (-) |
in DRIVERS KICK PANEL or BCM, (BLACK, 15-PIN PLUG), PIN 7, NOTE #2 |
DOMELIGHT
SUPERVISION |
BLUE (-) |
in PASSENGER A Pillar or BCM, (BLACK, 15-PIN PLUG), PIN 8, NOTE #2 |
TRUNK RELEASE |
YELLOW/BROWN (-) (Hatch Glass), NOTE #5 |
in PASSENGER KICK PANEL or BCM, (BLACK, 40-PIN PLUG), PIN 30, NOTE #2 |
SLIDING
POWER DOOR |
N/A |
|
HORN |
RED/WHITE (-) |
@ HORN Switch, (GRAY, 8-PIN PLUG), PIN 2 |
TACH |
Any wire NOT WHITE (AC) |
@ Any FUEL-INJECTOR |
WAIT TO
START LIGHT |
N/A |
|
BRAKE |
RED/GREEN to RED/BLACK (+) |
@ BRAKE PEDAL SWITCH or in EITHER KICK PANEL, Harness to REAR of Vehicle |
FACTORY
ALARM DISARM |
Use UNLOCK wire |
|
ANTI-THEFT |
INFINITI'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, See NOTE #1 |
|
EXTRA
INFORMATION |
NOTE #1: NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module,
Part # 791 or XK02 (For REMOTE START ONLY)
Part # DLPK-CANBUS MULTI (for REMOTE START and DOOR LOCKS)
NOTE #2: the BCM (Body Control Module) is located Under the DRIVERS SIDE DASH, to the
RIGHT of the Steering Column.
NOTE #3: TEST this wire while Turning the KEY in the Drivers Door. This wire will also ARM the
FACTORY ALARM.
NOTE #4: TEST this wire while Turning the KEY in the Drivers Door. This wire will also DISARM the
FACTORY ALARM.
NOTE #5: TEST this wire while opening the HATCH GLASS with the Handle on the REAR of the
Vehicle.
On vehicles with POWER LIFTGATE, the Open/Close wire is a BLUE/WHITE (-) located
in the DRIVERS KICK PANEL, Harness to REAR of Vehicle or at the POWER LIFTGATE
Switch, (GRAY, 6-PIN PLUG), PIN 1.
|
|
|
|
|