Vehicle
Wiring Details for your
2007-2011 Nissan Titan Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2007-2011 Nissan Titan . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
GREEN (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN LUG), PIN 3 |
| STARTER |
BROWN (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN LUG), PIN 2 |
| STARTER
2 |
LT. GREEN (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN LUG), PIN 6 |
| IGNITION
1 |
BLACK/RED (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN LUG), PIN 1 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
RED (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN LUG), PIN 4 |
| ACCESSORY/HEATER
BLOWER 2 |
PURPLE (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN LUG), PIN 5 |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
N/A |
|
| PARKING
LIGHTS ( + ) |
RED/BLUE (+) |
@ ELECTRIC BRAKE Pre-wiring Harness, (WHITE, 6-PIN PLUG), PIN 4, NOTE #5 |
| POWER LOCK |
BLUE (TYPE B), NOTE #3 |
@ POWER WINDOW Main Switch, (WHITE, 16-PIN PLUG), PIN 6 or 4 |
| POWER UNLOCK |
RED (TYPE B), Requires Double Pulse, NOTE #4 |
@ POWER WINDOW Main Switch, (WHITE, 16-PIN PLUG), PIN 7 or 6 |
| DOOR TRIGGER |
LT. BLUE (-) |
in DRIVERS KICK PANEL or BCM, (BLACK, 15-PIN PLUG), PIN 10, NOTE #2 |
| DOMELIGHT
SUPERVISION |
BLUE (-) |
@ DRIVERS KICK A Pillar or BCM, (BLACK, 15-PIN PLUG), PIN 8, NOTE #2 |
| TRUNK RELEASE |
N/A |
|
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
RED/WHITE (-) |
@ HORN Switch, (GRAY, 8-PIN PLUG), PIN 2, Under Steering Column cover |
| TACH |
Any wire NOT WHITE (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
RED/GREEN to RED/BLACK (+) |
@ BRAKE PEDAL Switch or in PASSENGER KICK PANEL, Harness to REAR of vehicle |
| FACTORY
ALARM DISARM |
Use UNLOCK wire |
|
| ANTI-THEFT |
NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is Equipped with NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM,
for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an
Extra Ignition key. (Requires extra key for Operation)
Part # XK09 for REMOTE STARTING ONLY, requires 1 key for
programming, NO key required for Operation.
Part # DB-ALL for REMOTE START/KEYLESS Entry, requires 1 key for programming
and NO Key for Operation.
To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: the BCM (Body Control Module) is located under the Drivers Dash and to the RIGHT of
the Steering Column.
NOTE #3: TEST this wire while Turning the KEY in the Drivers Door. This wire will also ARM the
FACTORY ALARM.
NOTE #4: TEST this wire while Turning the KEY in the Drivers Door. This wire will also DISARM the
FACTORY ALARM.
NOTE #5: the ELECTRIC BRAKE Pre-wiring Harness is located Under the DRIVERS DASH, and to
the RIGHT of the STEERING COLUMN.
|
|
|
|
|
|
