Vehicle
Wiring Details for your
2007-2009 Hyundai Santa Fe Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2007-2009 Hyundai Santa Fe . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
RED (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 5 |
| STARTER |
GREEN (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 1 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
ORANGE (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 6 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
RED (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 3 |
| ACCESSORY/HEATER
BLOWER 2 |
YELLOW (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN 4 |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BLUE/ORANGE (-) |
@ HEADLIGHT SWITCH or BCM, (26-PIN PLUG), PIN 1, NOTE #2 |
| PARKING
LIGHTS ( + ) |
GREEN(+)(Left) and YELLOW(+)(Right), use both |
@ FUSE BOX, (GRAY, 18-PIN PLUG), PINS 3 and 4 |
| POWER LOCK |
BLUE/BLACK (TYPE B) |
in DRIVERS KICK PANEL, (BROWN, 24-PIN PLUG), PIN 18 or BCM, (26-PIN PLUG), PIN 20, NOTE #2 |
| POWER UNLOCK |
GRAY/BLACK (TYPE B), Requires Double Pulse, NOTE #3 |
in DRIVERS KICK PANEL, (BROWN, 24-PIN PLUG), PIN 19 or BCM, (26-PIN PLUG), PIN 7, NOTE #2 |
| DOOR TRIGGER |
ORANGE (-) |
in PASSENGER KICK PANEL, (YELLOW, 22-PIN PLUG), PIN 17 or BCM, (26-PIN PLUG), PIN 15, NOTE #2 |
| DOMELIGHT
SUPERVISION |
BROWN (-) |
@ BCM, (14-PIN PLUG), PIN 4, NOTE #2 |
| TRUNK RELEASE |
N/A |
|
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
YELLOW/BLACK (-) |
@ HORN SWITCH or in DRIVERS KICK PANEL, (GREEN 24-PIN PLUG), PIN 20 |
| TACH |
NOTE #4 |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
NOTE #5 |
@ BRAKE PEDAL SWITCH |
| FACTORY
ALARM DISARM |
PINK and GRAY (-), Requires Double Pluse, NOTE #3 |
in DRIVERS KICK PANEL, (BROWN, 24-PIN PLUG), PINS 6 and 4 or BCM, (26-PIN PLUG), PINS 21 and 6, NOTE #2 |
| ANTI-THEFT |
HYUNDAI'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: HYUNDAI'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, ONLY if it is
a CANADIAN MODEL
Part # 791 Bypass for REMOTE START Requires extra Ignition key in bypass for
Operation.
to order go to the SECURITY BYPASS MODULE Page on this website
NOTE #2: the BCM, (Body Control Module) is located under the DRIVERS DASH, behind the
FUSE BOX.
NOTE #3: Use the UNLOCK wire, GRAY/BLACK (-) and both the FACTORY ALARM DIS-ARM wire,
PINK/GRAY(-) and the UNLOCK Detection wire, GRAY(-) all 3 wires must be used to
UNLOCK the Doors, also Requires a DOUBLE PULSE. TEST these wires while TURNING
the KEY in the DRIVERS DOOR.
NOTE #4: When using a TACH wire, us any wire NOT PINK on the 2.7L Engine and on the 3.3L
Engine us any wire NOT ORANGE, both will test (AC)
NOTE #5: for the BRAKE wire, use the GREEN/BLACK(+) on the 2.7L Engine and on the
3.3L Engine use the GRAY/BLACK (+), BOTH will be at the BRAKE PEDAL SWITCH.
|
|
|
|
|
|
