Hyundai Santa Fe 2007-2009 Printer Friendly Wiring Chart

Hyundai Santa Fe 2007-2009

PART	COLOR	LOCATION
12 VOLT CONSTANT	RED (+)	@ IGNITION SWITCH, (6-PIN PLUG), PIN 5
STARTER	GREEN (+)	@ IGNITION SWITCH, (6-PIN PLUG), PIN 1
STARTER 2	N/A
IGNITION 1	ORANGE (+)	@ IGNITION SWITCH, (6-PIN PLUG), PIN 6
IGNITION 2	N/A
IGNITION 3	N/A
ACCESSORY/HEATER BLOWER 1	RED (+)	@ IGNITION SWITCH, (6-PIN PLUG), PIN 3
ACCESSORY/HEATER BLOWER 2	YELLOW (+)	@ IGNITION SWITCH, (6-PIN PLUG), PIN 4
KEYSENSE	N/A
PARKING LIGHTS ( - )	BLUE/ORANGE (-)	@ HEADLIGHT SWITCH or BCM, (26-PIN PLUG), PIN 1, NOTE #2
PARKING LIGHTS ( + )	GREEN(+)(Left) and YELLOW(+)(Right), use both	@ FUSE BOX, (GRAY, 18-PIN PLUG), PINS 3 and 4
POWER LOCK	BLUE/BLACK (TYPE B)	in DRIVERS KICK PANEL, (BROWN, 24-PIN PLUG), PIN 18 or BCM, (26-PIN PLUG), PIN 20, NOTE #2
POWER UNLOCK	GRAY/BLACK (TYPE B), Requires Double Pulse, NOTE #3	in DRIVERS KICK PANEL, (BROWN, 24-PIN PLUG), PIN 19 or BCM, (26-PIN PLUG), PIN 7, NOTE #2
DOOR TRIGGER	ORANGE (-)	in PASSENGER KICK PANEL, (YELLOW, 22-PIN PLUG), PIN 17 or BCM, (26-PIN PLUG), PIN 15, NOTE #2
DOMELIGHT SUPERVISION	BROWN (-)	@ BCM, (14-PIN PLUG), PIN 4, NOTE #2
TRUNK RELEASE	N/A
SLIDING POWER DOOR	N/A
HORN	YELLOW/BLACK (-)	@ HORN SWITCH or in DRIVERS KICK PANEL, (GREEN 24-PIN PLUG), PIN 20
TACH	NOTE #4	@ Any FUEL-INJECTOR
WAIT TO START LIGHT	N/A
BRAKE	NOTE #5	@ BRAKE PEDAL SWITCH
FACTORY ALARM DISARM	PINK and GRAY (-), Requires Double Pluse, NOTE #3	in DRIVERS KICK PANEL, (BROWN, 24-PIN PLUG), PINS 6 and 4 or BCM, (26-PIN PLUG), PINS 21 and 6, NOTE #2
ANTI-THEFT	HYUNDAI'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, See NOTE #1	@ IGNITION SWITCH TUMBLER

EXTRA INFORMATION

NOTE #1: HYUNDAI'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, ONLY if it is a CANADIAN MODEL Part # 791 Bypass for REMOTE START Requires extra Ignition key in bypass for Operation. to order go to the SECURITY BYPASS MODULE Page on this website NOTE #2: the BCM, (Body Control Module) is located under the DRIVERS DASH, behind the FUSE BOX. NOTE #3: Use the UNLOCK wire, GRAY/BLACK (-) and both the FACTORY ALARM DIS-ARM wire, PINK/GRAY(-) and the UNLOCK Detection wire, GRAY(-) all 3 wires must be used to UNLOCK the Doors, also Requires a DOUBLE PULSE. TEST these wires while TURNING the KEY in the DRIVERS DOOR. NOTE #4: When using a TACH wire, us any wire NOT PINK on the 2.7L Engine and on the 3.3L Engine us any wire NOT ORANGE, both will test (AC) NOTE #5: for the BRAKE wire, use the GREEN/BLACK(+) on the 2.7L Engine and on the 3.3L Engine use the GRAY/BLACK (+), BOTH will be at the BRAKE PEDAL SWITCH.