Vehicle
Wiring Details for your
2006-2010 Dodge Viper SRT/10 Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2006-2010 Dodge Viper SRT/10 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
RED (+) |
@ IGNITION SWITCH, PIN 5 |
| STARTER |
YELLOW/ORANGE to PINK/ORANGE (+) |
@ STARTER Switch, Pin 3 or BCM, (BLACK/WHITE PLUG(C3) Pin 27, Note #1 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
RED/ORANGE (+) |
@ IGNITION SWITCH, PIN 3 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
BROWN/PURPLE (-) thru a Resistor |
@ IGNITION SWITCH, PIN 2 or BCM, (BLACK/GRAY PLUG(C2) Pin 20, Note #1 |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
WHITE/BLACK (-) |
@ HEADLIGHT Switch or BCM, (BLACK/GRAY PLUG(C2) Pin 21, Note #1 |
| PARKING
LIGHTS ( + ) |
WHITE/YELLOW (+) |
@ BCM, (BLACK/GREEN PLUG(C4) Pin 33, Note #1 |
| POWER LOCK |
LT. GREEN/YELLOW (-) thru a 1.5K Ohm Resistor |
@BCM, (BLACK/WHITE PLUG(C3) Pin 21, Note #1 |
| POWER UNLOCK |
Use LOCK wire, (-) thru a 249 Ohm Resistor |
|
| DOOR TRIGGER |
PURPLE (-) |
@ BCM, (BLACK/WHITE PLUG(C3) Pin 6, Note #1 |
| DOMELIGHT
SUPERVISION |
BLACK/BROWN (+) |
@ BCM, (BLACK/GRAY PLUG(C2) Pin 12, Note #1 |
| TRUNK RELEASE |
PURPLE/TAN (-) |
@ BCM, (BLACK/WHIE PLUG(C3) Pin 18, Note #1 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
DK. GREEN/WHITE (-) |
@ BCM, (BLACK/GREEN PLUG(C4) Pin 17, Note #1 |
| TACH |
Any wire NOT PINK/DK. BLUE or PINK/BROWN (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
WHITE/TAN (+) |
@ BRAKE SWITCH, PIN 2 |
| FACTORY
ALARM DISARM |
PURPLE/ LT. BLUE (-) thru a 1.97K Ohm Resistor |
@ BCM, (BLACK/white PLUG(C3) Pin 14, Note #1 |
| ANTI-THEFT |
TRANSPONDER |
REQUIRES INTERFACE MODULE SEE NOTE #2 BELOW |
| EXTRA
INFORMATION |
| Note #1: the BCM, (Body Control Module) is located in the Drivers Kick Panel
Note #2: Ignition system is MUX wire type with a transponder , requires interface module use
PKUMUX, PKUCH2GX, or PKUCG2X.
|
|
|
|
|
|
