Vehicle
Wiring Details for your
2005- Dodge Viper SRT/10 Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2005- Dodge Viper SRT/10 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
RED (+) |
@ IGNITION SWITCH HARNESS |
| STARTER |
YELLOW/ORANGE (+) or PINK/ORANGE (+) |
@ STARTER SWITCH or BCM, Connector C3, Pin 27, See NOTE #1 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
RED/ORANGE (+) |
@ IGNITION SWITCH HARNESS |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
WHITE/BLACK (-) |
@ BCM, Connector C4, Pin 21, See NOTE #1 |
| PARKING
LIGHTS ( + ) |
WHITE/YELLOW (+) |
@ BCM, Connector C2, Pin 33, See NOTE #1 |
| POWER LOCK |
LIGHT GREEN/YELLOW (1-Wire System), See NOTE #2 |
@ BCM, Connector C3, Pin 21, See NOTE #1 |
| POWER UNLOCK |
Same wire, See DIAGRAM |
See DIAGRAMS |
| DOOR TRIGGER |
PURPLE (-) and PURPLE/WHITE (-) Use both, See NOTE #3 |
@ BCM, Connector C3, Pins 6 and 16, See NOTE #1 |
| DOMELIGHT
SUPERVISION |
BLACK/BROWN (+) |
@ BCM, Connector C4, Pin 12, See NOTE #1 |
| TRUNK RELEASE |
WHITE/TAN to WHITE (+) |
@ BCM, Connector C2, Pin 32, See NOTE #1 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
DARK GREEN/WHITE (-) |
@ BCM, Connector C2, Pin 17, See NOTE #1 |
| TACH |
Any wire NOT BROWN/WHITE (AC) |
@ Any IGNITION COIL |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
WHITE/TAN (+) |
@ SWITCH ABOVE BRAKE PEDAL |
| FACTORY
ALARM DISARM |
PURPLE/LIGHT BLUE (-) See NOTE *4 |
@ BCM, Connector C3, Pin 14, See NOTE #1 |
| ANTI-THEFT |
N/A |
|
| EXTRA
INFORMATION |
| NOTE #1: the BCM (Body Control Module) is located in the DRIVERS KICK PANEL.
NOTE #2: this vehicle uses a 1-Wire Door Locking System, a (-)Negative thru a 1500 Ohm
Resistor will LOCK and a (-)Negative thru a 250 Ohm Resistor will UNLOCK, some
units will also require 2 extra relays part #775, to connect, See DIAGRAM
NOTE #3: when connecting to an ALARM SYSTEM use both DOOR TRIGGER wires and DIODE
ISOLATE, to connect, See DIAGRAM
NOTE #4: this vehicle Disarms with a (-) Negative thru a 2210 Ohm resistor and an extra relay
part #775, to connect. See DIAGRAM
|
|
|
|
|
|
