Vehicle
Wiring Details for your
2004-2007 Pontiac Grand Prix Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2004-2007 Pontiac Grand Prix . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
RED (+) |
@ BACK of FUSEBOX, PASSENGER UNDERDASH |
| STARTER |
YELLOW (+) |
@ IGNITION SWITCH HARNESS |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
PINK (+) See NOTE #1 |
@ IGNITION SWITCH HARNESS |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
BROWN (+) |
@ IGNITION SWITCH HARNESS |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BROWN/WHITE (-) |
@ BCM, 18 Pin Plug, Pin 8, See NOTE #2 |
| PARKING
LIGHTS ( + ) |
BROWN (+) |
FRONT of FUSEBOX, PASSENGER UNDERDASH |
| POWER LOCK |
RED/BLACK (TYPE B) |
@ BCM, Connector C2, Pin 2, See NOTE #2 |
| POWER UNLOCK |
ORANGE/BLACK (TYPE B) |
@ BCM, Connector C2, Pin 11, See NOTE #2 |
| DOOR TRIGGER |
See NOTE #3 |
@ BCM, See NOTE #2 |
| DOMELIGHT
SUPERVISION |
GRAY/BLACK (+) |
@ the UNDER DASH LIGHT or BCM, Connector C1, Pin 43, See NOTE #2 |
| TRUNK RELEASE |
LIGHT BLUE (+) |
@ BCM, Connector C2, Pin 45, See NOTE #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
BROWN (-) |
@ BCM, 18 Pin Plug, Pin 9, See NOTE #2 |
| TACH |
WHITE (AC) |
@ IGNITION CONTROL Module Pin E, See NOTE #4 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
WHITE (+) |
@ BCM, Connector C2, Pin 30, See NOTE #2 |
| FACTORY
ALARM DISARM |
PURPLE (-) |
@ BCM, Connector C2, Pin 24, See NOTE #2 |
| ANTI-THEFT |
GM's PASSKEY 3 (PK3 on Steel Shaft of Ignition Key) TRANSPONDER SYSTEM |
TRANSPONDER @ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: there are (2) PINK (+) wires that test as an Ignition wire, to test for the correct PINK IGNITION wire. Place the Key in the Ignition Switch but do not turn to the ON position. Try the remote starter, if the KEY in the IGNITION CHIME turns on, you are energizing the correct PINK Ignition wire.
NOTE #2: the BCM (Body Control Module) is located at the far end of the Drivers Dash, to access remove the Left END of the the Driver Dash it is just snapped into place then remove the under dash panel that is held into place with (3) plastic push-pins. Next remove the lower dash cover, this is held in place with (3) scres, one behind the Left END of the drives dash cover and (2) along the bottom of the dash. Next remove the Steel Knee bolster, it had (4) 10mm bolts that hould it into place on either side of the steering column. Now you can access the BCM, the BCM is hel into place by (3) 7mm screws on the face of the dash panel. The C2 54-pin connector for the BCM can be accessed from the Left END cover of the dash, the C1 54-pin connector and C3,18-PIN connector are side by side and are plugged into the BCM and face the floor of the vehicle, the C, 54-pin connector is to the left and the C3,18-PIN is to the right.
NOTE #3: the DRIVERS DOOR is a GRAY/BLACK (-) Pin 26, the PASSENGER DOOR is a BLACK/WHITE (-) Pin 17, the DRIVERS SIDE REAR DOOR is a LIGHT BLUE/BLACK (-) Pin 7 and the PASSENGERS SIDE REAR DOOR is a LIGHT GREEN/BLACK Pin 5 all are at the BCM Connector C2. When connecting to an ALARM SYSTEM, use all (4) DOOR TRIGGER wires and DIODE ISOLATE. to connect, See DIAGRAM
NOTE #4: the IGNITION CONTROL MODULE is located on the TOP of the ENGINE, towards the PASSENGER SIDE.
|
|
|
|
|
|
