Vehicle
Wiring Details for your
2004-2007 Dodge Caravan Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2004-2007 Dodge Caravan . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
Connect to BATTERY ONLY |
|
| STARTER |
YELLOW (+) (20 Gauge) |
@ IGNITION SWITCH HARNESS, BLACK Plug |
| STARTER
2 |
PURPLE/BROWN (-) (20 Gauge), See NOTE #1 |
@ IGNITION SWITCH HARNESS, BLACK Plug, See DIAGRAM |
| IGNITION
1 |
PINK/WHITE (+) (20 Gauge) (2 Wires, use either wire) |
@ IGNITION SWITCH HARNESS, BLACK Plug |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
WHITE/BROWN (-), See NOTE #2 |
@ HEADLIGHT SWITCH, BLACK Plug, See DIAGRAM |
| PARKING
LIGHTS ( + ) |
N/A |
|
| POWER LOCK |
PURPLE/GREEN (1-Wire Door Lock System), See NOTE #3 |
@ BCM, BLACK plug, Plug 2, See DIAGRAM |
| POWER UNLOCK |
Same wire, See DIAGRAM |
See DIAGRAM |
| DOOR TRIGGER |
See NOTE #4 |
@ BCM, BLACK Plug, Plug 2, See NOTE #5 |
| DOMELIGHT
SUPERVISION |
YELLOW/BROWN (+) |
@ BCM, BLACK Plug, Plug 2, See NOTE #5 |
| TRUNK RELEASE |
PURPLE/TAN (-), See NOTE #6 |
@ BCM, GREEN Connector , Pin 6, See DIAGRAM |
| SLIDING
POWER DOOR |
PURPLE/BLUE (-), See NOTE #7 |
@ BCM, BLACK Plug, Plug 2, See DIAGRAM |
| HORN |
GREEN/PURPLE (-) |
@ STEERING COLUMN HARNESS, WHITE Plug |
| TACH |
See NOTE #8 |
@ COIL PACK |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
WHITE/TAN (+) |
@ SWITCH ABOVE BRAKE PEDAL |
| FACTORY
ALARM DISARM |
DISARMS with FACTORY REMOTE ONLY |
|
| ANTI-THEFT |
CHRYSLERS MULTIPLEX IGNITION/ANTI-THEFT SYSTEM, Rquires INTERFACE BYPASS MODULE, SEE NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This vehicle Requires a Special INTERFACE BYPASS MODULE due to its MULTIPLEXED
IGNITION/ANTI-THEFT SYSTEM, it will Require Part # DB-ALL, Module will Interface
with the IGNITION/ANTI-THEFT System, KEYLESS ENTRY and TRUNK Release
with nothing else needed, to order go to the INTERFACE BYPASS MODULE Page on this
website........SPECIAL NOTE....You can use the 791 and an extra Ignition key BUT you
MUST build the RELAY and RESISTOR circuit as shown to remote start!!
NOTE #2: To turn on the PARKING LIGHTS requires a (-)Negative thru a 2000 Ohm resistor and
an extra relay part #775 to connect, See DIAGRAM
NOTE #3: This vehicle uses a 1-Wire Door Locking System requiring a (-)Negative thru a 5200
Ohm Resistor for LOCK, and a (-)Negative thru a 2000 Ohm Resistor for UNLOCK,
some units will also require 2 extra relays part #775 to connect, See DIAGRAMS
Also SEE NOTE #1
NOTE #4: This vehicle uses 4 door pin trigger wires, the DRIVERS DOOR is a PURPLE (-) at PIN
6, the PASSENGERS DOOR is a PURPLE/WHITE (-) PIN 7, the DRIVERS SIDE SLIDING
DOOR is a PURPLE/GRAY, PIN 8 and the PASSENGER SIDE SLIDING DOOR is a
PURPLE/YELLOW, PIN 5. When connecting to an ALARM SYSTEM use all 4 wires and
DIODE ISOLATE. See DIAGRAM
NOTE #5: The BCM (Body Control Module is located in the DRIVERS KICK PANEL, near the
PARKING BRAKE. The BCM has 5 Plugs, (1) 6-Pin Plug, and (4) 34-Pin PLugs.
NOTE #6: The Rear Hatch Pop is a (-) Negative thru a 1500 Ohm Resistor and requires an
extra relay part #775 to connect, See DIAGRAM
NOTE #7: The SLIDING DOORS require a (-)Negative thru a 1500 Ohm Resistor for the
DRIVERS SIDE and a (-)Negative thru a 2700 Ohm Resistor for the PASSANGER SIDE
and 2 extra relays part #775 for each door, See DIAGRAM.
NOTE #8: The TACH wire on the 2.4L is BLUE/GREEN or BLUE/TAN. On the 3.3L and 3.8L use
the BLUE/GREEN, BLUE/TAN or BLUE/ORANGE
|
|
|
|
|
|
