Vehicle
Wiring Details for your
2008- Chrysler Pacifica Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2008- Chrysler Pacifica . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
PURPLE/RED (+) |
@ BCM, (Plug(C1) Pin 1 , Note #2 |
| STARTER |
YELLOW (+) |
@ IGNITION SWITCH, (BLACK 5-Pin Plug) Pin 4 |
| STARTER
2 |
PURPLE/BROWN (-) thru a 180 Ohm Resistor, See NOTE #1 |
@ IGNITION SWITCH, (BLACK 5-Pin Plug) Pin 2 |
| IGNITION
1 |
PINK/GRAY (+) |
@ IGNITION SWITCH, (BLACK 5-Pin Plug) Pin 3 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
Use STARTER 2, (-) thru a 560 Ohm Resistor, See NOTE #1 |
|
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BROWN/WHITE (-) THRU A 920 Ohm Resistor |
@ HEADLIGHT Switch or BCM, (Plug(C5) Pin 31, Note #2 |
| PARKING
LIGHTS ( + ) |
N/A |
|
| POWER LOCK |
PURPLE/LT. BLUE (-) thru a 1.8K Ohm Resistor, Note #3 |
@ DDM, (BLACK, 20-Pin Plug) Pin 13, Note #4 |
| POWER UNLOCK |
Use LOCK wire, (-) thru a 750 Ohm Resistor, Double Pulse, See Note #3 |
|
| DOOR TRIGGER |
PURPLE (-) |
@ DDM, (BLACK, 20-Pin Plug) Pin 11, Note #4 |
| DOMELIGHT
SUPERVISION |
YELLOW/WHITE (+) (Front) and YELLOW/ORANGE (+) (Dome Light) |
@ DRIVERS A Pillar or BCM, Plug(C2) Pins 6 and 7, Note #2 |
| TRUNK RELEASE |
TAN/DK. GREEN (-) thrua 4.7K Ohm Resistor, Note #5 |
@ BCM, (Plug(C2) Pin 30, Note #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
DK. GREEN/PURPLE (-) |
@ HORN Switch |
| TACH |
Any wire NOT BROWN/GRAY (3.8L) or PINK/BROWN (4.0L) (AC) |
@ Any FUEL INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
WHITE/DK. GREEN (+) |
@ BRAKE Switch |
| FACTORY
ALARM DISARM |
See Note #3 |
|
| ANTI-THEFT |
CHRYSLER'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| Note #1: CHRYSLERS TRANSPONDER SYSTEM, Requires Bypass Module, Part # DB-ALL or XK09
with NO RESISTORS OR RELAYS REQUIRED for REMOTE STARTING and KEYLESS
ENTRY, to order go to the INTERFACE BYPASS MODULE Page on this website.
Note #2: the BCM, (Body control Module) is located under the Drivers side of the Dash,
on the Firewall.
Note #3: the LOCK/UNLOCK wire is the Factory Alarm ARM/DISARM wire. On Base Models
this wire is not present. You will need to add this wire to the pin location. The wire
next to this open pin (13 on Base Models) is a ORANGE/TAN, Pin 12 and
LT. BLUE/WHITE, Pin 13.
Note #4: the DDM (Drivers Door Module) is part of the Power Window Switch in the Door.
Note #5: TEST this wire while opening the Liftgate from the Handle on the Rear of the Vehicle.
Vehicles with Power Liftgate, use a PURPLE/TAN(-) thru a 4.7K Ohm Resistor
@ BCM, Plug(C2) Pin 29.
|
|
|
|
|
|
