| PART | COLOR | LOCATION |
| 12 VOLT CONSTANT | PURPLE/RED (+) | @ BCM, (Plug(C1) Pin 1 , Note #2 |
| STARTER | YELLOW (+) | @ IGNITION SWITCH, (BLACK 5-Pin Plug) Pin 4 |
| STARTER 2 | PURPLE/BROWN (-) thru a 180 Ohm Resistor, See NOTE #1 | @ IGNITION SWITCH, (BLACK 5-Pin Plug) Pin 2 |
| IGNITION 1 | PINK/GRAY (+) | @ IGNITION SWITCH, (BLACK 5-Pin Plug) Pin 3 |
| IGNITION 2 | N/A | |
| IGNITION 3 | N/A | |
| ACCESSORY/HEATER BLOWER 1 | Use STARTER 2, (-) thru a 560 Ohm Resistor, See NOTE #1 | |
| ACCESSORY/HEATER BLOWER 2 | N/A | |
| KEYSENSE | N/A | |
| PARKING LIGHTS ( - ) | BROWN/WHITE (-) THRU A 920 Ohm Resistor | @ HEADLIGHT Switch or BCM, (Plug(C5) Pin 31, Note #2 |
| PARKING LIGHTS ( + ) | N/A | |
| POWER LOCK | PURPLE/LT. BLUE (-) thru a 1.8K Ohm Resistor, Note #3 | @ DDM, (BLACK, 20-Pin Plug) Pin 13, Note #4 |
| POWER UNLOCK | Use LOCK wire, (-) thru a 750 Ohm Resistor, Double Pulse, See Note #3 | |
| DOOR TRIGGER | PURPLE (-) | @ DDM, (BLACK, 20-Pin Plug) Pin 11, Note #4 |
| DOMELIGHT SUPERVISION | YELLOW/WHITE (+) (Front) and YELLOW/ORANGE (+) (Dome Light) | @ DRIVERS A Pillar or BCM, Plug(C2) Pins 6 and 7, Note #2 |
| TRUNK RELEASE | TAN/DK. GREEN (-) thrua 4.7K Ohm Resistor, Note #5 | @ BCM, (Plug(C2) Pin 30, Note #2 |
| SLIDING POWER DOOR | N/A | |
| HORN | DK. GREEN/PURPLE (-) | @ HORN Switch |
| TACH | Any wire NOT BROWN/GRAY (3.8L) or PINK/BROWN (4.0L) (AC) | @ Any FUEL INJECTOR |
| WAIT TO START LIGHT | N/A | |
| BRAKE | WHITE/DK. GREEN (+) | @ BRAKE Switch |
| FACTORY ALARM DISARM | See Note #3 | |
| ANTI-THEFT | CHRYSLER'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 | @ IGNITION SWITCH TUMBLER |
| EXTRA INFORMATION |
| Note #1: CHRYSLERS TRANSPONDER SYSTEM, Requires Bypass Module, Part # DB-ALL or XK09 with NO RESISTORS OR RELAYS REQUIRED for REMOTE STARTING and KEYLESS ENTRY, to order go to the INTERFACE BYPASS MODULE Page on this website. Note #2: the BCM, (Body control Module) is located under the Drivers side of the Dash, on the Firewall. Note #3: the LOCK/UNLOCK wire is the Factory Alarm ARM/DISARM wire. On Base Models this wire is not present. You will need to add this wire to the pin location. The wire next to this open pin (13 on Base Models) is a ORANGE/TAN, Pin 12 and LT. BLUE/WHITE, Pin 13. Note #4: the DDM (Drivers Door Module) is part of the Power Window Switch in the Door. Note #5: TEST this wire while opening the Liftgate from the Handle on the Rear of the Vehicle. Vehicles with Power Liftgate, use a PURPLE/TAN(-) thru a 4.7K Ohm Resistor @ BCM, Plug(C2) Pin 29. |