Vehicle
Wiring Details for your
1999-2000 Plymouth Prowler Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 1999-2000 Plymouth Prowler . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
PINK/BLACK (+) and RED/YELLOW (+) |
IGNITION SWITCH HARNESS |
| STARTER |
YELLOW (+) |
IGNITION SWITCH HARNESS |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
BLUE (+) |
IGNITION SWITCH HARNESS |
| IGNITION
2 |
RED/WHITE (+) (thin wire) |
IGNITION SWITCH HARNESS |
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
BLACK/ORANGE (+) |
IGNITION SWITCH HARNESS |
| ACCESSORY/HEATER
BLOWER 2 |
BLACK/WHITE (+) |
IGNITION SWITCH HARNESS |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
LIGHT GREEN/RED (-) |
@ BCM, Connector C1, Pin 40, See NOTE *1 |
| PARKING
LIGHTS ( + ) |
BLACK/YELLOW (+) |
@ BLUE, 22-Pin plug, above BRAKE |
| POWER LOCK |
ORANGE/VIOLET (TYPE A) |
@ BCM, Connector 2, Pin 41, See NOTE *1 |
| POWER UNLOCK |
PINK/VIOLET (TYPE A) |
@ BCM, Connector 2, Pin 75, See NOTE *1 |
| DOOR TRIGGER |
TAN and TAN/RED (-) See NOTE *2 |
@ BCM, Connector C2, Pins 79 and 48, See NOTE *1 |
| DOMELIGHT
SUPERVISION |
TAN (-) See NOTE *2 |
@ BCM, Connector C2, Pin 48, See NOTE *1 |
| TRUNK RELEASE |
YELLOW/RED (+) See NOTE *3 |
@ RELAY BEHIND GLOVEBOX |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
BLACK/RED (-) |
@ BCM, Connector C1, Pin 17, See NOTE *1 |
| TACH |
GRAY/LIGHT BLUE |
@ TACH on STEERING COLUMN, pin 1 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
WHITE/TAN (+) |
@ STEERING COLUMN HARNESS |
| FACTORY
ALARM DISARM |
LIGHT GREEN/BLACK (-) See NOTE *4 |
@ BCM, Connector C2, Pin 45, See NOTE *1 |
| ANTI-THEFT |
CHRYSLER'S SENTRY KEY (GRAY KEY ONLY) A TRANSPONDER SYSTEM |
TRANSPONDER @ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE *1 the BCM (Body Control Module) is located in the DRIVERS KICK PANEL, Connector #1 (WHITE) is on TOP towards the FRONT of the vehicle and Connector #2 (WHITE) is on TOP towards the REAR, Connector #3 (BLACK) is on the BOTTOM.
NOTE *2 the TAN (-) Pin 79, is for the DRIVERS DOOR and the TAN/RED (-) Pin 48, is for the PASSENGER DOOR. When connecting to an ALARM SYSTEM, use both DOOR TRIGGER wires and DIODE ISOLATE. to connect, See DIAGRAM.
NOTE *3 CAUTION!!!! The REAR of the CONVERTIBLE TOP must be UNLATCHED and FOLDED forward BEFORE using the TRUNK RELEASE.
NOTE *4 a (-) Negative pulsed output on this wire thru a 663 Ohm Resistor, will DISARM the FACTORY ALARM SYSTEM, without UNLOCKING the doors.
|
|
|
|
|
|
