Chrysler  Sebring Sedan 2004-2007
 PART   COLOR  LOCATION
 12 VOLT CONSTANT   PINK/BLACK (+) and RED (+)   @ IGNITION SWITCH HARNESS
 STARTER  YELLOW (+)  @ IGNITION SWITCH HARNESS
 STARTER 2  N/A  
 IGNITION 1  BLUE (+)  @ IGNITION SWITCH HARNESS
 IGNITION 2  GREEN/RED (+) 20 Gauge wire  @ IGNITION SWITCH HARNESS
 IGNITION 3  N/A  
 ACCESSORY/HEATER BLOWER 1  BLACK/ORANGE (+)  @ IGNITION SWITCH HARNESS
 ACCESSORY/HEATER BLOWER 2  BLACK/WHITE (+)  @ IGNITION SWITCH HARNESS
 KEYSENSE  N/A  
 PARKING LIGHTS ( - )  N/A  
 PARKING LIGHTS ( + )  BLACK/YELLOW (+)  IN DRIVERS KICK PANEL or HEADLIGHT SWITCH
 POWER LOCK  WHITE/GREEN (1-Wire Door Lock System), See NOTE #2  @ BCM, Connector 4, Pin 15, See DAIGRAM
 POWER UNLOCK  Same wire, See DIAGRAM  See DIAGRAMS
 DOOR TRIGGER  See NOTE #5  @ BCM, Connector 4, Pins 5 and 6, See NOTE #4
 DOMELIGHT SUPERVISION  YELLOW (-), (Requires #775 Relay)  @ FRONT of FUSEBOX, 6-Pin Plug
 TRUNK RELEASE  GREEN/WHITE (5-Wire), See NOTE #6  @ BCM, Connector 4, Pin 1, See NOTE #4
 SLIDING POWER DOOR  N/A  
 HORN  BLACK/RED (-)  @ STEERING COLUMN HARNESS
 TACH  ANY wire that is NOT GREEN/LIGHT GREEN (AC)  @ Any COIL or FUEL INJECTOR
 WAIT TO START LIGHT  N/A  
 BRAKE  WHITE/TAN (+)  @ SWITCH ABOVE BRAKE PEDAL
 FACTORY ALARM DISARM   LIGHT GREEN/ORANGE (+), See NOTE #3  @ BCM, Connector 4, Pin 4, See NOTE #4
 ANTI-THEFT  CHRYSLER'S ANTI-THEFT TRANSPONDER System (GRAY IGNITION KEY), See NOTE #1  TRANSPONDER @ IGNITION SWITCH TUMBLER
 EXTRA INFORMATION
 NOTE #1: If you vehicle has the ANTI-THEFT KEY, a INTERFACE BYPASS MODULE Part # DB-ALL or XK09 that will BYPASS the ANTI-THEFT SYSTEM and it will also bypass the need for the resistors on the door locks, to order please go to the INTERFACE BYPASS MODULE page on this website NOTE #2: This vehicle uses a 1-Wire Door Locking System that requires a (+)Positive thru a 2700 Ohm Resistor to LOCK and a (+)Positive thru a 620 Ohm Resistor to UNLOCK, some units will also require 2 extra relays part #775 to connect, See DIAGRAM NOTE #3: To DISARM requires a (+)Positive thru a 750 Ohm Resistor and an extra Relay part #775 to connect, See DIAGRAM NOTE #4; The BCM (Body Control Module) is located under the DRIVERS SIDE of DASH and is attached to the FUSE/RELAY box. Connector 4 is a 26 pin plug at the bottom edge of the BCM. NOTE #5: this vehicle uses 4 door pin triggers, at the BCM Connector 4, the DRIVERS DOOR is a TAN (-) Pin 5, the PASSENGERS DOOR is a TAN/RED (-) Pin 6, the DRIVERS REAR DOOR is a TAN/ORANGE (-) Pin 7 and the PASSENGER REAR DOOR is a TAN/YELLOW, Pin 8. When connecting to an ALARM SYSTEM, use all 4 wires and DIODE ISOLATE. See DIAGRAM NOTE #6: the TRUNK/HATCH Release on this vehicle is a 5-Wire System and will require an extra Relay Part #775, to connect, See DIAGRAM.