PART | COLOR | LOCATION |
12 VOLT CONSTANT | PINK/BLACK (+) | @ IGNITION SWITCH HARNESS |
STARTER | YELLOW (+) | @ IGNITION SWITCH HARNESS |
STARTER 2 | N/A | |
IGNITION 1 | DARK BLUE (+) | @ IGNITION SWITCH HARNESS |
IGNITION 2 | DARK GREEN/RED (+) 20 Gauge wire | @ IGNITION SWITCH HARNESS |
IGNITION 3 | N/A | |
ACCESSORY/HEATER BLOWER 1 | BLACK/ORANGE (+) | @ IGNITION SWITCH HARNESS |
ACCESSORY/HEATER BLOWER 2 | BLACK/WHITE (+) or BLACK/LIGHT BLUE (+) | @ IGNITION SWITCH HARNESS |
KEYSENSE | N/A | |
PARKING LIGHTS ( - ) | N/A | |
PARKING LIGHTS ( + ) | BLACK/YELLOW (+) | IN DRIVERS KICK PANEL or HEADLIGHT SWITCH |
POWER LOCK | WHITE/DARK GREEN (1-Wire Door Lock System), See NOTE #2 | @ BCM, Connector 4, Pin 15, See NOTE #3 |
POWER UNLOCK | Same wire, See DIAGRAM | See DIAGRAMS |
DOOR TRIGGER | TAN (-) and TAN/RED (-) use both, See NOTE #5 | @ BCM, Connector 4, Pins 5 and 6, See NOTE #3 |
DOMELIGHT SUPERVISION | YELLOW (-), (Requires #775 Relay) | @ FRONT of FUSEBOX, 6-Pin Plug |
TRUNK RELEASE | BLACK/WHITE (5-Wire), See NOTE #6 | @ BCM, Connector 4, Pin 1, See NOTE #3 |
SLIDING POWER DOOR | N/A | |
HORN | BLACK/RED (-) | @ BCM, Connector 1, Pin 2, See NOTE #3 |
TACH | Any wire NOT DARK GREEN/ORANGE or DARK GREEN/LIGHT GREEN (AC) | @ Any IGNITION COIL |
WAIT TO START LIGHT | N/A | |
BRAKE | WHITE/TAN (+) | @ SWITCH ABOVE BRAKE PEDAL |
FACTORY ALARM DISARM | LIGHT GREEN/ORANGE (+), See NOTE #4 | @ BCM, Connector 4, Pin 4, See NOTE #3 |
ANTI-THEFT | CHRYSLER'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 | @ IGNITION SWITCH TUMBLER |
EXTRA INFORMATION |
NOTE #1: This vehicle may be equipped with CHRYSLER'S ANTI-THEFT TRANSPONDER System (GRAY IGNITION KEY), if so to remote start will require the 791 BYPASS MODULE and an extra Ignition key, to order go to the SECURITY BYPASS MODULE PAGE on this website. NOTE #2: This vehicle uses a 1-Wire Door Locking System that requires a (+)Positive thru a 2700 Ohm Resistor to LOCK and a (+)Positive thru a 620 Ohm Resistor to UNLOCK, Use 1/2 watt resistors from Radio Shack, to get 620 ohms, use a 470 + 150 ohms in series, for 2700 ohms use 2.2k + 470 ohm in series. Some units will also require 2 extra relays part #775, to connect, See DIAGRAM You can also get a INTERFACE BYPASS MODULE the Part # XK09 that will do this for you without adding extra relays and resistors, these Modules will also do dome light supervision and trunk pop with nothing needed, to order please go to the INTERFACE BYPASS MODULE Page on this website NOTE #3: The BCM (Body Control Module) is located under the DRIVERS SIDE of DASH and is attached to the FUSE/RELAY box. NOTE #4: To DISARM requires a (+)Positive thru a 750 Ohm Resistor use 1/2 watt resistors , use a 680 + 68 ohm in series, and an extra Relay part #775, to connect, See DIAGRAM NOTE #5: When connecting to an ALARM SYSTEM, use both wires and DIODE ISOLATE, See DIAGRAM NOTE #6: the TRUNK/HATCH Release on this vehicle is a 5-Wire System that will require an extra Relay Part #775 to connect, See DIAGRAM. |