Chrysler  Concorde 2004-
 PART   COLOR  LOCATION
 12 VOLT CONSTANT   PINK/BLACK (+) and RED (+)   @ IGNITION SWITCH HARNESS
 STARTER  YELLOW (+)  @ IGNITION SWITCH HARNESS
 STARTER 2  N/A  
 IGNITION 1  DARK BLUE/WHITE (+)  @ IGNITION SWITCH HARNESS
 IGNITION 2  DARK GREEN/RED (+)  @ IGNITION SWITCH HARNESS
 IGNITION 3  N/A  
 ACCESSORY/HEATER BLOWER 1  BLACK/ORANGE (+)  @ IGNITION SWITCH HARNESS
 ACCESSORY/HEATER BLOWER 2  BLACK/WHITE (+)  @ IGNITION SWITCH HARNESS
 KEYSENSE  N/A  
 PARKING LIGHTS ( - )  YELLOW (-) See NOTE #2  @ HEADLIGHT SWITCH, See DIAGRAM
 PARKING LIGHTS ( + )  BLACK/YELLOW (+)  @ BACK of JUNCTION BLOCK, GRAY Plug, Pin 11
 POWER LOCK  WHITE/DARK GREEN (1-Wire Door Lock System) See NOTE #3  @ BCM, BLUE Plug, Pin 5, See NOTE #4
 POWER UNLOCK  Same wire, See DIAGRAM  See DIAGRAMS
 DOOR TRIGGER  See NOTE #6  @ BCM BLUE PLUG, See NOTE #4
 DOMELIGHT SUPERVISION  YELLOW (-), (Requires #775 Relay)  @ FRONT of JUNCTION BLOCK, BROWN Plug Pin 4
 TRUNK RELEASE  BLACK/WHITE (+)  @ TRUNK RELEASE SWITCH
 SLIDING POWER DOOR  N/A  
 HORN  BLACK/RED (-)  @ BACK of JUNCTION BLOCK, GRAY Plug, Pin 6
 TACH  See NOTE #5  @ IGNITION COIL PACK
 WAIT TO START LIGHT  N/A  
 BRAKE  WHITE/TAN (+)  @ SWITCH ABOVE BRAKE PEDAL
 FACTORY ALARM DISARM   LIGHT GREEN/ORANGE (+) See NOTE #7  @ BCM. BLUE Plug, Pin 13, See NOTE #4
 ANTI-THEFT  CHRYSLER'S ANTI-THEFT TRANSPONDER System, See NOTE #1  TRANSPONDER @ IGNITION SWITCH TUMBLER
 EXTRA INFORMATION
 NOTE #1: This vehicle may be equipped with CHRYSLER'S ANTI-THEFT TRANSPONDER System (GRAY IGNITION KEY), if so to remote start will require the 791 BYPASS MODULE and an extra Ignition key, to order go to the SECURITY BYPASS MODULE PAGE on this website. NOTE #2: the PARKING LIGHTS require an extra relay Part #775 and a (-)Negative thru a 47 Ohm Resistor, to connect, See DIAGRAM NOTE #3: the DOOR LOCKS on this vehicle require a (+)Positive thru a 2700 Ohm resistor to LOCK and a (+)Positive thru a 620 Ohm resistor to UNLOCK, some units will also require 2 extra relays part #775 for the keyless entry feature to function, See DIAGRAMS.You can also get a INTERFACE BYPASS MODULE the Part # XK09 that will do this for you without adding extra relays and resistors, these Modules will also do dome light supervision and trunk pop with nothing needed, to order please go to the INTERFACE BYPASS MODULE Page on this website NOTE #4: The BCM (Body Control Module) is located on the LEFT SIDE of the dash attached to the JUNCTION BLACK. NOTE #5: This vehicle uses a Multi-Coil system, for TACH use any wire at the coil pack that is NOT DARK GREEN/LIGHT GREEN NOTE #6: the DRIVERS DOOR is a TAN (-) PIN 4, the PASSENGER DOOR is a TAN/RED (-) PIN 2, the DRIVERS REAR DOOR is a TAN/RED (-) PIN 1 and the PASSENGER REAR DOOR is a TAN/RED (-) PIN 10. When connecting to an ALARM SYSTEM, use all 4 wires and DIODE ISOLATE See DIAGRAM NOTE #7: the DISARM wire requires an extra relay part #775 and a (+)Positive thru a 680 Ohm Resistor, to connect, See DIAGRAM.