Toyota Highlander Hybrid 2008-2010 Printer Friendly Wiring Chart

Toyota Highlander Hybrid 2008-2010

PART	COLOR	LOCATION
12 VOLT CONSTANT	BLACK (+)	@ DASH FUSE BOX, (WHITE, 1-Pin Plug(A) Pin 1
STARTER	PINK (+)	@ ENGINE SWITCH (GRAY, 14-Pin Plug) Pin 7
STARTER 2	BROWN (+)	@ ENGINE SWITCH (GRAY, 14-Pin Plug) Pin 2
IGNITION 1	WHITE (+)	@ DASH FUSE BOX, (REAR, WHITE, 10-Pin Plug(I) Pin 7
IGNITION 2	LT. BLUE (+)	@ DASH FUSE BOX, (REAR, WHITE, 10-Pin Plug(I) Pin 9
IGNITION 3	N/A
ACCESSORY/HEATER BLOWER 1	GRAY (+)	@ DASH FUSE BOX, (REAR, WHITE, 10-Pin Plug(I) Pin 3
ACCESSORY/HEATER BLOWER 2	N/A
KEYSENSE	N/A
PARKING LIGHTS ( - )	LT. BLUE (-)	@ HEADLIGHT SWITCH, (WHITE, 20-Pin Plug) Pin 18
PARKING LIGHTS ( + )	N/A
POWER LOCK	ORANGE (TYPE B), NOTE #2	in DRIVERS KICK PANEL, (BLACK, 18-Pin Plug) Pin 8
POWER UNLOCK	GREEN (TYPE B), NOTE #3	in DRIVERS KICK PANEL, (BLACK, 18-Pin Plug) Pin 9
DOOR TRIGGER	BLUE (-)	in DRIVERS KICK PANEL, (BLACK, 18-Pin Plug) Pin 15
DOMELIGHT SUPERVISION	LT. BLUE (-)	@ DASH FUSE BOX, (WHITE, 12-Pin Plug(R) Pin 5
TRUNK RELEASE	YELLOW to BROWN (-) (Liftgate), ORANGE to BROWN (-) (Glass) NOTE #4	in DRIVERS KICK PANEL, (GRAY, 12-Pin Plug) Pin 1, (BLACK, 18-Pin Plug) Pin 13
SLIDING POWER DOOR	N/A
HORN	YELLOW to GRAY (-)	@ HORN SWITCH or DASH FUSE BOX, (WHITE, 16-Pin Plug(D) Pin 11
TACH	N/A
WAIT TO START LIGHT	N/A
BRAKE	BLUE (+)	@ BRAKE SWITCH or DASH FUSE BOX, (WHITE, 12-Pin Plug(P) Pin 3
FACTORY ALARM DISARM	PURPLE (-) (Requires Double Pulse), See NOTE #5	in DRIVERS KICK PANEL, (BLACK, 18-Pin Plug) Pin 12
ANTI-THEFT	TOYOTA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1	@ IGNITION SWITCH TUMBLER

EXTRA INFORMATION

NOTE #1: TOYOTA'S TRANSPONDER SYSTEM, Requires Bypass Module: (For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation. (For Remote Starting Only) Part # PK-ALL Bypass. (No Extra Key Required for Operation) 2-KEYS Required to Program Module. (For Remote Starting/Door Locks) Part # DB-ALL (No Extra Key Required for Operation) 1-KEY Required for Programming. To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS MODULE Page on this website. NOTE #2: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Arm wire. NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Disarm wire. NOTE #4: TEST this wire while opening the Liftge or Glass from the Handle on the Rear of the Vehicle. On vehicles with Power Liftgate, the Open/Close wire is a RED (-) @ the switch on the Dash, (BLUE, 5-Pin Plug) Pin 4. NOTE #5: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock the Doors.