Mazda  Mazda 6 2009-2011
 PART   COLOR  LOCATION
 12 VOLT CONSTANT   RED/BLUE (+)   @ IGNITION SWITCH, (6-PIN PLUG), PIN F
 STARTER  GRAY/RED (+), NOTE #6  @ IGNITION SWITCH, (6-PIN PLUG), PIN A
 STARTER 2  BLACK/GREEN and BLACK/RED (-) (PUSH-BUTTON START)  @ PUSH-BUTTON START SWITCH or KCM, (12-PIN PLUG), PINS J and K, NOTE #10
 IGNITION 1  GREEN/YELLOW (+), NOTE #7  @ IGNITION SWITCH, (6-PIN PLUG), PIN C
 IGNITION 2  N/A  
 IGNITION 3  N/A  
 ACCESSORY/HEATER BLOWER 1  PINK/YELLOW (+), NOTE #8  @ IGNITION SWITCH, (6-PIN PLUG), PIN B
 ACCESSORY/HEATER BLOWER 2  YELLOW (+), NOTE #9  @ IGNITION SWITCH, (6-PIN PLUG), PIN D
 KEYSENSE  N/A  
 PARKING LIGHTS ( - )  BLACK/WHITE (-)  @ HEADLIGHT SWITCH, (17-PIN PLUG), PIN L
 PARKING LIGHTS ( + )  RED/BLUE (+)  @ BCM,(16-PIN PLUG(8), PIN O, NOTE #2
 POWER LOCK  BLACK/WHITE (TYPE B)(-)Negative , NOTE #3  @ BCM,(16-PIN PLUG(6), PIN G, NOTE #2
 POWER UNLOCK  Use LOCK wire  
 DOOR TRIGGER  BLACK/YELLOW (-) N.C.  @ BCM,(16-PIN PLUG(8), PIN B, NOTE #2
 DOMELIGHT SUPERVISION  BLACK/BLUE (-)  @ BCM,(16-PIN PLUG(6), PIN M, NOTE #2
 TRUNK RELEASE  BLACK/RED (-)  @ BCM,(30-PIN PLUG(3), PIN X, NOTE #2
 SLIDING POWER DOOR  N/A  
 HORN  BLACK (-)  @ BCM,(30-PIN PLUG(3), PIN V, NOTE #2
 TACH  Any wire NOT RED(4 Cyl) or BLUE(V6) (AC)  @ Any FUEL-INJECTOR
 WAIT TO START LIGHT  N/A  
 BRAKE  RED/WHITE (+)  @ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle
 FACTORY ALARM DISARM   Disarms with INTERFACE MODULE, See NOTE #4  
 ANTI-THEFT  MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1  
 EXTRA INFORMATION
 NOTE #1: This vehicle is with MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an Extra Ignition key. (Requires extra key for Operation) Part # PK-ALL or PKFM for REMOTE STARTING ONLY, requires 2 keys for programming, NO key required for Operation. Part # DB-ALL for Remote Starting and Keyless Entry operation (no resistors required), 2 keys required for programming, no key required for Operation. To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS MODULE Page on this website. NOTE #2: the BCM, (Body Control Module) is located in the DRIVERS KICK PANEL. NOTE #3: This Vehicle requires a INTERFACE BYPASS MODULE for the KEYLESS ENTRY Function NOTE #4: this Vehicle ARMS/DISARMS with INTERFACE BYPASS MODULE NOTE #5: TEST this wire while Opening the Trunk/Liftgate from the Release Button on the REAR of the Vehicle. NOTE #6: On vehicles with the PUSH-BUTTON Start, this wire is at the KCM, (GRAY, 27-PIN PLUG), PIN B. The KCM (Keyless Control Module) is located under the Drivers Dash NOTE #7: On vehicles with the PUSH-BUTTON Start, this wire is a PINK/BLUE (+)located at the RELAY BLOCK, (6-PIN PLUG), PIN B. The RELAY BLOCK is located under the DRIVERS DASH, close to the Steering Column. NOTE #8: On vehicles with the PUSH-BUTTON Start, this wire is located at the RELAY BLOCK, (6-PIN PLUG), PIN F. The RELAY BLOCK is located under the DRIVERS DASH and to the LEFT of the Steering Column. NOTE #9: On vehicles with the PUSH-BUTTON Start, this wire is located at the RELAY BLOCK, (8-PIN PLUG), PIN B. The RELAY BLOCK is located under the DRIVERS DASH and to the LEFT of the Steering Column. NOTE #10: The KCM (Keyless Control Module) is located under the Drivers Dash