Lexus Hs250h 2010-2011 Printer Friendly Wiring Chart

Lexus Hs250h 2010-2011

PART	COLOR	LOCATION
12 VOLT CONSTANT	BLACK (+)	@ DASH FUSE BOX, (WHITE, 1-PIN PLUG(E), PIN 1
STARTER	BLUE (-) and PURPLE (-)	@ ENGINE SWITCH, (BLACK, 14-PIN PLUG), PIN 7 and 2
STARTER 2	GRAY (+)	WHITE 26-PIN PLUG, PIN 25, HIGH behind DASH FUSEBOX
IGNITION 1	WHITE (+)	@ DASH FUSE BOX, (WHITE, 40-PIN PLUG(C), PIN 2
IGNITION 2	PINK (+)	@ DASH FUSE BOX, (REAR, WHITE, 40-PIN PLUG(B), PIN 25
IGNITION 3	N/A
ACCESSORY/HEATER BLOWER 1	GRAY (+)	@ DASH FUSE BOX, (REAR, WHITE, 56-PIN PLUG(A), PIN 43
ACCESSORY/HEATER BLOWER 2	N/A
KEYSENSE	N/A
PARKING LIGHTS ( - )	WHITE/BLACK (-)	@ BECU, (BLACK, 30-PIN PLUG), PIN 30, NOTE #5
PARKING LIGHTS ( + )	BROWN (+)
POWER LOCK	BLUE (TYPE B), (TEST with PASSENGER Switch), NOTE #2	@ BECU, (BLACK, 30-PIN PLUG), PIN 9, NOTE #5
POWER UNLOCK	LT. BLUE (TYPE B), (TEST with PASSENGER Switch), NOTE #3	@ BECU, (BLACK, 30-PIN PLUG), PIN 10, NOTE #5
DOOR TRIGGER	BLUE (-)	@ DASH FUSE BOX, (REAR, WHITE, 40-PIN PLUG(B), PIN 13
DOMELIGHT SUPERVISION	BLUE (-)	@ DASH FUSE BOX, (REAR, WHITE, 40-PIN PLUG(B), PIN 27
TRUNK RELEASE	WHITE (-)	@ BECU, (WHITE, 28-PIN PLUG), PIN 5, NOTE #5
SLIDING POWER DOOR	N/A
HORN	BLACK (-)	@ DASH FUSE BOX, (WHITE, 40-PIN PLUG(C), PIN 24
TACH	BLUE (AC)	@ DATA LINK Connector, (WHITE, 16-PIN PLUG), PIN 9, under Drivers Dash
WAIT TO START LIGHT	N/A
BRAKE	LT. GREEN (+)	@ BRAKE SWITCH or DASH FUSE BOX, (WHITE, 36-PIN PLUG(D), PIN 3
FACTORY ALARM DISARM	BROWN (-) Requires Double Pulse, NOTE #4	@ BECU, (BLACK, 30-PIN PLUG), PIN 24, NOTE #5
ANTI-THEFT	TOYOTA'S TRANSPONDER SYSTEM, See NOTE #1

EXTRA INFORMATION

NOTE #1: LEXUS TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, Part # 791 Bypass Module (for REMOTE STARTING ONLY!) an Extra Ignition key is required to be placed inside this module for Operation. Part # DB-ALL Bypass Module, this Module is a KEYLESS BYPASS MODULE and DOES NOT require a Key to be placed inside the Module for Operation, this module will also do the Keyless Entry. To order the Bypass Module go to the INTERFACE BYPASS MODULE Page on this website NOTE #2: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Arm wire. NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Disarm wire. NOTE #4: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock the Doors. NOTE #5: the BECU, (Body Electronic Control Unit) is located under the Drivers Dash, attached to the Right side of the DASH FUSE BOX.