Jeep  Liberty 2004-
 PART   COLOR  LOCATION
 12 VOLT CONSTANT   PINK/BLACK (+) and RED (+)   @ IGNITION SWITCH HARNESS
 STARTER  YELLOW (+)  @ IGNITION SWITCH HARNESS
 STARTER 2  N/A  
 IGNITION 1  RED/DARK BLUE (+)  @ IGNITION SWITCH HARNESS
 IGNITION 2  N/A  
 IGNITION 3  N/A  
 ACCESSORY/HEATER BLOWER 1  BLACK/ORANGE (+)  @ IGNITION SWITCH HARNESS
 ACCESSORY/HEATER BLOWER 2  BLACK/WHITE (+)  @ IGNITION SWITCH HARNESS
 KEYSENSE  N/A  
 PARKING LIGHTS ( - )  LIGHT GREEN/ORANGE (-) See NOTE #2  @ HEADLIGHT SWITCH or BCM GRAY 22 PIN , PIN 5 See NOTE *5, See DAIGRAM
 PARKING LIGHTS ( + )  DO NOT USE!!!  
 POWER LOCK  PINK/PURPLE (1-Wire Door Lock System) See NOTE #3  @ REAR of FUSE BOX, TOP LEFT Plug, Pin 14, See DIAGRAM
 POWER UNLOCK  Same wire, See DIAGRAM  See DIAGRAMS
 DOOR TRIGGER  See NOTE #4  @ BCM, See NOTE *5
 DOMELIGHT SUPERVISION  YELLOW (-), Requires Part #775 Relay  @ REAR of FUSE BOX, TOP LEFT PLUG, PIN 30
 TRUNK RELEASE  ORANGE/PINK (-)  @ BCM, GRAY 26-Pin plug, Pin 17, See NOTE #6
 SLIDING POWER DOOR  N/A  
 HORN  BLACK/RED (-)  @ HORN SWITCH
 TACH  ANY wire NOT DARK GREEN/ORANGE  @ any FUEL-INJECTOR or IGNITION COIL
 WAIT TO START LIGHT  N/A  
 BRAKE  WHITE/TAN (+)  @ SWITCH ABOVE BRAKE PEDAL
 FACTORY ALARM DISARM   LIGHT GREEN/ORANGE (-) See NOTE #5  @ BCM, GRAY 22-PIN PLUG, PIN 9, See NOTE #6
 ANTI-THEFT  CHRYSLER'S SENTRY KEY, A TRANSPONDER SYSTEM, See NOTE #1  TRANSPONDER @ IGNITION SWITCH TUMBLER
 EXTRA INFORMATION
 NOTE #1; This vehicle requires the 791 BYPASS MODULE for REMOTE STARTING, an Extra Ignition key is also required and will need to be placed inside the 791 for Operation, to order please go to the SECURITY BYPASS MODULE Page on this website. NOTE #2: the PARKING LIGHTS require a (-)Negative thru a 1000 Ohm Resistor and an relay part #775, to connect, See DIAGRAM NOTE #3: to LOCK requires a (-)Negative thru a 1400 Ohm Resistor and UNLOCK requires a (-)Negative thru a 426 Ohm Resistor, some units will also require 2 extra relays part #775, to connect, See DIAGRAM NOTE #4: the DRIVERS DOOR is a TAN (-) in the GRAY 26-PIN plug, pin 4, the PASSENGER DOOR is a TAN/RED (-) in the GRAY 26-PIN plug, pin 5, the DRIVERS REAR DOOR is a TAN/ORANGE (-) in the GRAY 22-PIN plug, pin 3, the PASSENGER REAR DOOR (-) is a TAN/YELLOW (-) is a TAN/YELLOW (-) in the GRAY 26-PIN plug, pin 22. When connecting to an ALARM SYSTEM use all 4 DOOR TRIGGER wires and DIODE ISOLATE, to connect, See DIAGRAM NOTE #5: THE DISARM WIRE REQUIRES A (-)NEGATIVE THRU A 473 OHM RESISTOR AND AN EXTRA RELAY PART #775, TO CONNECT, See DIAGRAM NOTE #6: THE BCM (Body Control Module) IS ATTACHED TO THE LEFT OF THE FUSE BOX.