Vehicle
Wiring Details for your
2011- Toyota Highlander Wiring Diagram |
Printer Friendly Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2011- Toyota Highlander . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
|
PART |
COLOR |
LOCATION |
12 VOLT
CONSTANT |
BLACK (+) |
WHITE 1-PIN PLUG(1A), PIN 1, @ DASH FUSEBOX |
STARTER |
YELLOW (+) |
WHITE 8-PIN PLUG, PIN 7, @ IGNITION SWITCH |
STARTER
2 |
RED (+) |
WHITE 8-PIN PLUG, PIN 3, @ IGNITION SWITCH |
IGNITION
1 |
BLACK (+) |
WHITE 8-PIN PLUG, PIN 6, @ IGNITION SWITCH |
IGNITION
2 |
LT.BLUE (+) |
WHITE 8-PIN PLUG, PIN 1, @ IGNITION SWITCH |
IGNITION
3 |
N/A |
|
ACCESSORY/HEATER
BLOWER 1 |
GRAY (+) |
WHITE 8-PIN PLUG, PIN 2, @ IGNITION SWITCH |
ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
KEYSENSE |
LT. BLUE (-) |
WHITE 2-PIN PLUG, PIN 2, @ IGNITION KEY TUMBLER |
PARKING
LIGHTS ( - ) |
LT.BLUE (-) |
BLACK 20-PIN PLUG, PIN 18, @ HEADLIGHT SWITCH |
PARKING
LIGHTS ( + ) |
DO NOT USE!!! |
|
POWER LOCK |
TAN or LT.BLUE (TYPE B) |
BLACK 18-PIN PLUG, PIN 14, in DRIVERS KICK PANEL |
POWER UNLOCK |
GREEN (TYPE B) |
BLACK 18-PIN PLUG, PIN 9, in DRIVERS KICK PANEL |
DOOR TRIGGER |
BLUE (-) |
BLACK 18-PIN PLUG, PIN 15, in DRIVERS KICK PANEL |
DOMELIGHT
SUPERVISION |
LT.BLUE (-) |
WHITE 12-PIN PLUG(1R), PIN 5, @ DASH FUSEBOX |
TRUNK RELEASE |
YELLOW (-)(LIFTGATE), TAN (-)(GLASS) |
GRAY 12-PIN PLUG, PIN 1, or BLACK 18-PIN PLUG, PIN 13, IN DRIVERS KICK |
SLIDING
POWER DOOR |
N/A |
|
HORN |
YELLOW to GRAY (-) |
@ HORN SWITCH or WHITE 16-PIN PLUG(1D), PIN 11, @ DASH FUSEBOX |
TACH |
LT.BLUE (AC) |
WHITE 16-PIN PLUG, PIN 9 @ DATA LINK CONNECTOR |
WAIT TO
START LIGHT |
N/A |
|
BRAKE |
BLUE (+) |
@ BRAKE PEDAL SWITCH |
FACTORY
ALARM DISARM |
USE KEYSENSE WIRE |
|
ANTI-THEFT |
TOYOTA'S TRANSPONDER ANTI-THEFT SYSTEM, SEE NOTE #1 |
@ IGNITION SWITCH TUMBLER |
EXTRA
INFORMATION |
NOTE #1: TOYOTA'S TRANSPONDER SYSTEM, Requires Bypass Module:
(For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation.
(For Remote Starting/Door Locks) Part # DB-ALL (No Extra Key Required for Operation)
1-KEY Required for Programming.
To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
|
|
|
|
|