Vehicle
Wiring Details for your
2011- Honda Odyssey Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2011- Honda Odyssey . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
WHITE (+) |
@ IGNITION SWITCH, 5-PIN PLUG, PIN 1 |
| STARTER |
YELLOW (+) |
@ IGNITION SWITCH, 5-PIN PLUG, PIN 2 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
BLUE (+) or PINK (+) |
@ IGNITION SWITCH, 5-PIN PLUG, PIN 3 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
ORANGE (+) |
@ IGNITION SWITCH, 5-PIN PLUG, PIN 5 |
| ACCESSORY/HEATER
BLOWER 2 |
RED (+) |
@ IGNITION SWITCH, 5-PIN PLUG, PIN 4 |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
GRAY (-) |
@ HEADLIGHT SWITCH, 12-PIN PLUG, PIN 8 |
| PARKING
LIGHTS ( + ) |
RED (+) |
@ PASSENGER FUSEBOX, LT.GREEN 13-PIN PLUG(A), PIN 13 |
| POWER LOCK |
SEE NOTE #2 |
|
| POWER UNLOCK |
SEE NOTE #3 |
|
| DOOR TRIGGER |
LT. BLUE (-) |
@ DRIVER DASH FUSEBOX, 44-PIN PLUG(E), PIN 22 |
| DOMELIGHT
SUPERVISION |
PINK (-) |
@ DRIVER DASH FUSEBOX, REAR 16-PIN PLUG(G), PIN 10 |
| TRUNK RELEASE |
ORANGE (-), SEE NOTE #4 |
@ REAR FUSEBOX, 49-PIN PLUG(A), PIN 16 |
| SLIDING
POWER DOOR |
WHITE (-)(Open), BROWN (-)(Close), LT.GREEN(Common), SEE NOTE #5 |
@ POWER SLIDING DOOR SWITCH,12-PIN PLUG, PINS 8, 9 and 7 |
| HORN |
PURPLE (-) |
@ HORN SWITCH, 20-PIN PLUG, PIN 10 |
| TACH |
Any wire GREEN, RED, BLUE, TAN, PINK or LT.BLUE (AC) |
@ Any FUEL-INJECTOR, 2-PIN PLUG, PIN 1 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
LT.GREEN (+) |
@ BRAKE PEDAL SWITCH, 4-PIN PLUG, PIN 2 |
| FACTORY
ALARM DISARM |
SEE NOTE #3 |
|
| ANTI-THEFT |
HONDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: HONDA'S TRANSPONDER SYSTEM, Requires Bypass Module:
(For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation.
(For Remote Starting/Door Locks) Part # DB-ALL (No Extra Key Required for Operation)
1-KEY Required for Programming.
To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: To LOCK this vehicle, use the FACTORY ALARM ARM wire, PINK (TYPE B) at the
POWER WINDOW MASTER SWITCH, 37-PIN PLUG, PIN 35, this wire is also the DRIVER
DOOR KEY LOCK wire.
NOTE #3: To UNLOCK this vehcile, use the FACTORY ALARM DISARM wires, BROWN (TYPE B)
and a WHITE (TYPE B), Requires a DOUBLE PULSE to UNLOCK, these wires are located
at the POWER WINDOW MASTER SWITCH 37-PIN PLUG, PIN 34 and PIN 32. MUST diode isolate.
NOTE #4: On vehicles with POWER TAILGATE, when the Tailgate switch is pressed, it connects
the BROWN and YELLOW wires at the Switch a 6-PIN PLUG, PINS 4 and 5, or 17-PIN
PLUG, PINS15 and 14
NOTE #5: When the POWER SLIDING DOOR switch is pressed, it connect the Open to the
Common or the Closed to the Common.
|
|
|
|
|
|
