Vehicle
Wiring Details for your
2010-2012 Toyota 4-Runner Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2010-2012 Toyota 4-Runner . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
BLACK (+) |
@ DASH FUSE BOX, (WHITE, 1-Pin Plug(E), Pin 1 |
| STARTER |
RED (+) NOTE #2 |
@ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 8 |
| STARTER
2 |
BLACK (+) |
@ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 1 |
| IGNITION
1 |
BLACK (+) NOTE #3 |
@ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 6 |
| IGNITION
2 |
PURPLE (+) NOTE #4 |
@ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 4 |
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
RED (+) NOTE #5 |
@ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 3 |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
RED (-) |
@ BODY ECU, (WHITE, 30-Pin Plug), Pin 30, NOTE #6 |
| PARKING
LIGHTS ( + ) |
GREEN (+) |
@ DASH FUSE BOX, (WHITE, 36-Pin Plug(F), Pin 16 |
| POWER LOCK |
BLACK (TYPE B), (TEST using Passenger Switch) |
@ DASH FUSE BOX, (WHITE, 30-Pin Plug), Pin 9 |
| POWER UNLOCK |
WHITE (TYPE B), (TEST using Passenger Switch), NOTE #7 |
@ DASH FUSE BOX, (WHITE, 30-Pin Plug), Pin 10 |
| DOOR TRIGGER |
RED (-) |
@ DASH FUSE BOX, (WHITE, 36-Pin Plug(F), Pin 27 |
| DOMELIGHT
SUPERVISION |
GREEN (-) |
@ DASH FUSE BOX, (REAR, WHITE, 40-Pin Plug(B), Pin 18 |
| TRUNK RELEASE |
Use Trunk Release Motor wire |
|
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
GRAY/BLUE (-) |
@ DASH FUSE BOX, (WHITE, 40-Pin Plug(D), Pin 29 |
| TACH |
PINK (AC) |
@ DATA LINK Connector, (WHITE, 16-Pin Plug), Pin 9 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
PURPLE/GREEN to BLUE (+) |
@ BRAKE SWITCH or DASH FUSE BOX, (WHITE, 36-Pin Plug(F), Pin 29 |
| FACTORY
ALARM DISARM |
GRAY (-) (Requires Double Pulse) NOTE #8 |
@ BODY ECU, (WHITE, 30-Pin Plug), Pin 24, NOTE #6 |
| ANTI-THEFT |
TOYOTA'S TRANSPONDER SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: TOYOTA'S TRANSPONDER SYSTEM, Requires Bypass Module:
(For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation.
(For Remote Starting Only) Part # PK-ALL Bypass. (No Extra Key Required for
Operation) 2-KEYS Required to Program Module.
(For Remote Starting/Door Locks) Part # DB-ALL (No Extra Key Required for Operation)
1-KEY Required for Programming.
To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: on vehicles with SMART KEY, PUSH-BUTTON Start, the START Switch 1 wire is
LT. GREEN (-) and the START Switch 2 wire is RED (-) at the ENGINE Switch
(BLACK, 14-Pin Plug) Pins 7 and 2.
NOTE #3: on vehicles with SMART KEY, PUSH-BUTTON Start, the Ignition wire is a BLUE (+)
located in the DRIVERS KICK PANEL, (WHITE, 48-Pin Plug) Pin 7
NOTE #4: on vehicles with SMART KEY, PUSH-BUTTON Start, the Ignition 2 wire is a PURPLE (+)
located at the DASH FUSE BOX, (REAR, WHITE, 56-Pin Plug(C) Pin 52
NOTE #5: on vehicles with SMART KEY, PUSH-BUTTON Start, the ACCESSORY wire is a RED (+)
located at the DASH FUSE BOX, (REAR, WHITE, 56-Pin Plug(C) Pin 48
NOTE #6: the BODY ECU is located under the DRIVERS DASH, it is attached to the RIGHT side of
the DASH FUSE BOX.
NOTE #7: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Disarm wire.
NOTE #8: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock the
doors.
|
|
|
|
|
|
