Vehicle
Wiring Details for your
2010-2011 Toyota Prius Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2010-2011 Toyota Prius . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
WHITE (+) |
@ DASH FUSE BOX, (WHITE 1-Pin Plug(E) Pin 1 |
| STARTER |
SEE NOTE #1 |
|
| STARTER
2 |
N/A |
|
| IGNITION
1 |
SEE NOTE #1 |
|
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
SEE NOTE #1 |
|
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
YELLOW (-) |
@ BODY ECU, (WHITE, 30-Pin Plug) Pin 30, NOTE #6 |
| PARKING
LIGHTS ( + ) |
BROWN (+) |
@ DASH FUSE BOX, (WHITE 36-Pin Plug(D) Pin 18 |
| POWER LOCK |
LT. GREEN (TYPE B), (TEST with Passenger Switch) NOTE #2 |
@ BODY ECU, (WHITE, 30-Pin Plug) Pin 9, NOTE #6 |
| POWER UNLOCK |
BROWN (TYPE B), (TEST with Passenger Switch) NOTE #3 |
@ BODY ECU, (WHITE, 30-Pin Plug) Pin 10, NOTE #6 |
| DOOR TRIGGER |
PURPLE (-) |
@ DASH FUSE BOX, (WHITE 36-Pin Plug(D) Pin 35 |
| DOMELIGHT
SUPERVISION |
BLUE (-) |
@ DASH FUSE BOX, (REAR, WHITE 56-Pin Plug(A) Pin 52 |
| TRUNK RELEASE |
GRAY (-), NOTE #4 |
in DRIVERS KICK PANEL, (WHITE, 64-Pin Plug) Pin 46 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
LT. BLUE (-) |
@ DASH FUSE BOX, (WHITE 40-Pin Plug(C) Pin 24 |
| TACH |
N/A |
|
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
BLUE (+) |
@ BRAKE SWITCH or in DRIVERS KICK PANEL, (WHITE, 10-Pin Plug) Pin 5 |
| FACTORY
ALARM DISARM |
PURPLE (-) (Requires Double Pulse), NOTE #5 |
@ BODY ECU, (WHITE, 30-Pin Plug) Pin 24, NOTE #6 |
| ANTI-THEFT |
TOYOTA'S MULTIPLEX IGNITION CIRCUIT/ANTI-THEFT SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This Vehicle is Equipped with TOYOTA'S MULTIPLEX IGNITION CIRCUIT/ANTI-THEFT
SYSTEM that requires a INTERFACE BYPASS MODULE for REMOTE STARTING,
Part # DB-ALL to order please go to the INTERFACE BYPASS MODULE Page on this
website.
NOTE #2: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Arm wire.
NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Disarm wire.
NOTE #4: TEST this wire while opening the Hatch with the Handle on the Rear of the Vehicle.
NOTE #5: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock
the Doors.
NOTE #6: the BODY ECU is located under the Drivers Dash and is attached to the Right side
of the Dash Fuse Box.
|
|
|
|
|
|
