Vehicle
Wiring Details for your
2009-2010 Chrysler PT Cruiser Wiring Diagram |
Printer Friendly Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2009-2010 Chrysler PT Cruiser . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
|
PART |
COLOR |
LOCATION |
12 VOLT
CONSTANT |
RED (+) |
@ BATTERY |
STARTER |
PINK/LT.BLUE (+) |
@ IGNITION Switch, (BLACK, 5-Pin Plug) Pin 4 |
STARTER
2 |
PURPLE/BROWN (-) thru a 180 Ohm Resistor, See NOTE #1 |
@ IGNITION Switch, (BLACK, 5-Pin Plug) Pin 2 |
IGNITION
1 |
PINK/WHITE (+) |
@ IGNITION Switch, (BLACK, 5-Pin Plug) Pin 3 |
IGNITION
2 |
N/A |
|
IGNITION
3 |
N/A |
|
ACCESSORY/HEATER
BLOWER 1 |
Use STARTER 2 wire, (-) thru a 610 Ohm Resistor, See NOTE #1 |
|
ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
KEYSENSE |
N/A |
|
PARKING
LIGHTS ( - ) |
N/A |
|
PARKING
LIGHTS ( + ) |
WHITE/PURPLE (+) |
in DRIVERS KICK PANEL, Harness to Rear of Vehicle. |
POWER LOCK |
LT. GREEN/DK. GREEN (-) thru a 1000 Ohm Resistor, SEE NOTE #2 |
in DRIVERS KICK PANEL or INSTRUMENT CLUSTER, (BROWN, 20-Pin Plug) Pin 18 |
POWER UNLOCK |
Use LOCK wire, (-) thru a 249 Ohm Resistor, SEE NOTE #2 |
|
DOOR TRIGGER |
TAN to PURPLE(-) (Wagon), PURPLE (-) (Convertible), SEE NOTE #3 |
n DRIVERS KICK PANEL or INSTRUMENT CLUSTER, (BROWN, 20-Pin Plug) Pin 3 |
DOMELIGHT
SUPERVISION |
YELLOW/WHITE (+) |
in DRIVERS KICK PANEL or INSTRUMENT CLUSTER, (BROWN, 20-Pin Plug) Pin 4 |
TRUNK RELEASE |
TAN/DK. GREEN(-) (Wagon), TAN/LT. GREEN (-) (Convertible), SEE NOTE #4 |
in DRIVERS KICK PANEL or INSTRUMENT CLUSTER, (BLACK, 20-Pin Plug) Pin 13 |
SLIDING
POWER DOOR |
N/A |
|
HORN |
DK. GREEN/PURPLE (-) |
@HORN Switch or INSTRUMENT CLUSTER, (BLACK, 20-Pin Plug) Pin 10 |
TACH |
Any wire NOT DK. GREEN/ORANGE (AC) |
@ Any FUEL INJECTOR |
WAIT TO
START LIGHT |
N/A |
|
BRAKE |
DK. GREEN/WHITE (+) |
@ BRAKE SWITCH or INSTRUMENT CLUSTER, (BROWN, 20-Pin Plug) Pin 8 |
FACTORY
ALARM DISARM |
DISARMS with FACTORY REMOTE ONLY!! |
|
ANTI-THEFT |
CHRYSLER'S MULTIPLEX IGNITION/ANTI-THEFT SYSTEM, See Note #1 |
|
EXTRA
INFORMATION |
Note #1: CHRYSLER'S MULTIPLEX IGNITION/ANTI-THEFT SYSTEM, Requires INTERFACE BYPASS
MODULE Part # DB-ALL or XK09 that will BYPASS the ANTI-THEFT SYSTEM and BYPASS
the need for the above resistors and relays, it will also bypass the need for the
resistors on the door locks, to order please go to the INTERFACE BYPASS MODULE
page on this website
NOTE #2: This vehicle uses a 1-Wire Door Locking System, the LOCK requires a (-) Negative
thru a 1000 Ohm Resistor and the UNLOCK requires a (-) Negative thru a 250 Ohm
resistor, depending on the unit some will also require (2) 775 relays See DIAGRAMS.
also See NOTE #1
NOTE #3: The DRIVERS DOOR is a TAN (-) to PURPLE (-) in Pin 3, the PASSENGER DOOR is a
TAN/RED (-) to PURPLE/WHITE (-) in Pin 11. The DRIVERS REAR DOOR is a
TAN/ORANGE (-) to PURPLE/GRAY (-) in Pin 5. The PASSENGER REAR DOOR is a
TAN/YELLOW (-) to PURPLE/YELLOW (-) in Pin 6. When connecting to an ALARM
SYSTEM use all 4 wires and DIODE ISOLATE See DIAGRAM
NOTE #4: On CONVERTIBLE's the TRUNK RELEASE is at the Switch in the Glove box, on Wagon's
test this wire while opening the hatch from the handle on the rear hatch, the
TRUNK/HATCH Release Motor wire is a TAN/YELLOW (+) in the Drivers Kick Panel.
|
|
|
|
|