Vehicle
Wiring Details for your
2008-2012 Toyota Sequoia Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2008-2012 Toyota Sequoia . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
BLACK (+) |
@ DASH FUSEBOX, (WHITE, 1-Pin Plug(A) Pin 1 |
| STARTER |
GREEN (+) |
@ IGNITION SWITCH (WHITE, 8-Pin Plug) Pin 7 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
BLACK (+) |
@ IGNITION SWITCH (WHITE, 8-Pin Plug) Pin 6 |
| IGNITION
2 |
LT. GREEN (+) |
@ IGNITION SWITCH (WHITE, 8-Pin Plug) Pin 1 |
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
GRAY (+) |
@ IGNITION SWITCH (WHITE, 8-Pin Plug) Pin 2 |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BEIGE (-) |
@ HEADLIGHT Switch or BODY ECU, (WHITE, 26-Pin Plug) Pin 23, NOTE #5 |
| PARKING
LIGHTS ( + ) |
GREEN (+) |
@ DASH FUSEBOX, (WHITE, 24-Pin Plug(C) Pin 22 |
| POWER LOCK |
RED (TYPE B), (TEST with Passenger Switch), NOTE #2 |
@ DASH FUSEBOX, (REAR, WHITE, 66-Pin Plug(D) Pin 49 |
| POWER UNLOCK |
WHITE (TYPE B), (TEST with Passenger Switch), NOTE #3 |
@ DASH FUSEBOX, (REAR, WHITE, 66-Pin Plug(D) Pin 40 |
| DOOR TRIGGER |
BROWN (-) |
@ BODY ECU, (WHITE, 26-Pin Plug) Pin 24, NOTE #5 |
| DOMELIGHT
SUPERVISION |
BLUE (-) |
@ INTERIOR LIGHT Switch on Dash, (BLACK, 10-Pin Plug) Pin 10 |
| TRUNK RELEASE |
Use Trunk Motor wire, See NOTE #6 |
|
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
TAN to PURPLE (+) |
@ HORN SWITCH or @ DASH FUSE BOX, (WHITE, 24-Pin Plug(B) Pin 1 |
| TACH |
WHITE (AC) |
@ DATA LINK Connector, (WHITE, 16-Pin Plug) Pin 9 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
TAN (+) |
@ BRAKE SWITCH, (BLUE, 4-Pin Plug) Pin 1 |
| FACTORY
ALARM DISARM |
PINK (-) Requires double Pulse, NOTE #4 |
in DRIVERS KICK PANEL, (BLUE, 17-Pin Plug) Pin 16 |
| ANTI-THEFT |
TOYOTA'S TRANSPONDER SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: TOYOTA'S TRANSPONDER SYSTEM, Requires Bypass Module:
(For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation.
(For Remote Starting Only) Part # PK-ALL Bypass. (No Extra Key Required for
Operation) 2-KEYS Required to Program Module. (FITS 2008-2010 ONLY!!)
(For Remote Starting/Door Locks) Part # DB-ALL (No Extra Key Required for Operation)
1-KEY Required for Programming.
To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: this wire is only needed if the Door Locks do not function with the
Aftermarket System while the vehicle is running. All other times just use the Factory
Alarm Arm wire: Light Green in Drivers kick panel, Blue 17-pin plug, Pin 14
NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System
while the vehicle is running. All other times just use the Factory Alarm Disarm wire.
NOTE #4: TEST this wire while turning the Key in the Drivers Door, this wire will also Unlock
the Doors.
NOTE #5: the BODY ECU is located under the Drivers Dash and is attached to the Dash Fuse
Box.
NOTE #6: on Vehicles with Power Liftgate, the Open/Close wire is a RED (-) @ the Switch on the
Dash or the Body ECU, (WHITE, 26-Pin Plug) Pin 26.
|
|
|
|
|
|
