Vehicle
Wiring Details for your
2008-2010 Mazda Mazda 5 Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2008-2010 Mazda Mazda 5 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
BLACK/YELLOW (+) |
@ IGNITION SWITCH, (WHITE, 8-PIN PLUG), PIN 8 |
| STARTER |
BLACK/BLUE (+) |
@ IGNITION SWITCH, (WHITE, 8-PIN PLUG), PIN 5 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
BLUE (+) |
IGNITION SWITCH, (WHITE, 8-PIN PLUG), PIN 1 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
BLACK/RED (+) |
IGNITION SWITCH, (WHITE, 8-PIN PLUG), PIN 6 |
| ACCESSORY/HEATER
BLOWER 2 |
PURPLE (+) |
IGNITION SWITCH, (WHITE, 8-PIN PLUG), PIN 7 |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BROWN/RED (-) |
@ HEADLIGHT SWITCH or BCM, (30-PIN PLUG), PIN O, NOTE #2 |
| PARKING
LIGHTS ( + ) |
GRAY/BLACK (+) |
in PASSENGER KICK PANEL or BCM, (24-PIN PLUG(5), PIN R, NOTE #2 |
| POWER LOCK |
BLUE (TYPE B) (-)Negative, See NOTE #3 |
in DRIVERS KICK PANEL or BCM, (24-PIN PLUG(5), PIN I, NOTE #2 |
| POWER UNLOCK |
Use LOCK wire |
|
| DOOR TRIGGER |
BLUE/BLACK (-) N.C. |
in DRIVERS KICK PANEL or BCM, (24-PIN PLUG(5), PIN G, NOTE #2 |
| DOMELIGHT
SUPERVISION |
YELLOW (-) |
in PASSENGER KICK PANEL or BCM, (8-PIN PLUG(6), PIN I, NOTE #2 |
| TRUNK RELEASE |
LOCKS/UNLOCKS with DOOR LOCKS |
|
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
PURPLE/WHITE (-) |
@ HORN SWITCH or BCM, (30-PIN PLUG(3), PIN Y, NOTE #2 |
| TACH |
BLACK/WHITE, BLACK/YELLOW, BLACK/BLUE or BLACK/ORANGE (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
GREEN/YELLOW (+) |
@ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle |
| FACTORY
ALARM DISARM |
Disarms with INTERFACE MODULE |
|
| ANTI-THEFT |
MAZDA'S TRANPONDER ANTI-THEFT SYSTEM, Requires Bypass Module, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is with MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM,
for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an
Extra Ignition key. (Requires extra key for Operation)
Part # PK-ALL or PKFM for REMOTE STARTING ONLY, requires 2 keys for
programming, NO key required for Operation.
Part # DB-ALL for Remote Starting and Keyless Entry operation (no resistors
required), 2 keys required for programming, no key required for Operation.
To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: the BCM, (Body Control Module) is located Behind the GLOVE BOX.
NOTE #3: This Vehicle requires the INTERFACE BYPASS MODULE for KEYLESS ENTRY operation
|
|
|
|
|
|
