Vehicle
Wiring Details for your
2007-2011 Mitsubishi Outlander Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2007-2011 Mitsubishi Outlander . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
WHITE (+) |
@ FUSE BOX, (BLACK, 2-PIN PLUG), PIN 1 |
| STARTER |
ORANGE (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 5 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
WHITE (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 2 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
LT. GREEN (+) |
@ IGNITION SWITCH, (WHITE, 6-PIN PLUG), PIN 6 |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
N/A |
|
| PARKING
LIGHTS ( + ) |
YELLOW(+)(Left) and BROWN(+)(Right) (Requires 775 Relay) |
@ FUSE BOX, (WHITE, 20-PIN PLUG), PINS 10 and 13 |
| POWER LOCK |
WHITE/BLACK (TYPE B) |
in DRIVERS KICK PANEL, (BROWN, 24-PIN PLUG), PIN 2 |
| POWER UNLOCK |
RED/YELLOW (TYPE B) |
in DRIVERS KICK PANEL, (BROWN, 24-PIN PLUG), PIN 3 |
| DOOR TRIGGER |
YELLOW (-) |
@ FUSE BOX, (BROWN, 16-PIN PLUG), PIN 16 |
| DOMELIGHT
SUPERVISION |
YELLOW (-) |
@ FUSE BOX, (WHITE, 6-PIN PLUG), PIN 5 |
| TRUNK RELEASE |
BROWN (-)(Use RELEASE Motor wire if not Present), NOTE #2 |
@ FUSE BOX, (BROWN, 16-PIN PLUG), PIN 14 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
GREEN (-) |
@ HORN SWITCH or FUSE BOX, (WHITE, 19-PIN PLUG), PIN 19 |
| TACH |
Any wire NOT RED/WHITE(4-CYL) or BLUE(V6) (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
RED/WHITE or RED (+) |
@ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle |
| FACTORY
ALARM DISARM |
DISARMS with FACTORY REMOTE ONLY!! |
|
| ANTI-THEFT |
MITSUBISHI'S TRANSPONDER SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: MITSUBISHI'S TRANSPONDER ANTI-THEFT SYSTEM, Requires Bypass Module,
Part # 791 Bypass Module (for REMOTE STARTING ONLY!) an Extra Ignition key is
required to be placed inside this module for Operation.
Part # XK09 Bypass Module, this Module is a KEYLESS BYPASS MODULE and DOES
NOT require a Key to be placed inside the Module for Operation, this module will also
do the Keyless Entry.
To order go to the INTERFACE BYPASS MODULE Page on this website.
NOTE #2: TEST this wire while Opening the LIFTGATE from the Handle on the REAR of the
Vehicle.
|
|
|
|
|
|
