Vehicle
Wiring Details for your
2006-2009 Mercury Milan Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2006-2009 Mercury Milan . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
BROWN/RED (+) |
@ IGNITION SWITCH HARNESS |
| STARTER |
BLUE/WHITE (+) |
@ IGNITION SWITCH, 7-Pin Plug, Pin 7 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
WHITE/ORANGE (+) |
@ IGNITION SWITCH, 7-Pin Plug, Pin 1 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
PURPLE/GREEN (+) |
@ IGNITION SWITCH, 7-Pin Plug, Pin 6 |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
N/A |
|
| PARKING
LIGHTS ( + ) |
GRAY/YELLOW (+) |
IN DRIVERS KICK PANEL or SJB, Connector E, Pin 30, See NOTE #2 |
| POWER LOCK |
GRAY/YELLOW (TYPE B) |
IN DRIVER KICK PANEL or SJB, Connector C, Pin 4, See NOTE #2 and NOTE #3 |
| POWER UNLOCK |
PURPLE/GRAY (TYPE B) |
IN DRIVERS KICK PANEL or SJB, Connector C, Pin 10, See NOTE #2 and NOTE #3 |
| DOOR TRIGGER |
Use DOME LIGHT SUPERVISION wire |
|
| DOMELIGHT
SUPERVISION |
BLUE (+) |
IN DRIVERS KICK PANEL or SJB, Connector E, Pin 16, See NOTE #2 and NOTE #4 |
| TRUNK RELEASE |
BROWN (-) |
@ SJB, Connector D, Pin 27, See NOTE #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
BLUE/WHITE (-) |
@ HORN SWITCH or SJB, Connector B, Pin 6, See NOTE #2 |
| TACH |
Any wire NOT WHITE/BLUE (2.3L and 3.0L) and NOT PURPLE/GREEN (3.5L) (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
PURPLE/WHITE (+) |
@ SWITCH above BRAKE PEDAL or SJB, Connector A, Pin 19, See NOTE #2 |
| FACTORY
ALARM DISARM |
PURPLE/BROWN (-) |
IN DRIVERS KICK PANEL or SJB, Connector C, Pin 5, See NOTE #2 and NOTE #5 |
| ANTI-THEFT |
FORD'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is equipped with a Special Anti-theft key, to remote start you will
need a Bypass module 791, use this module IF you have a extra ignition key to
place inside the 791 to remote start, if you do not have an extra key to use or wish
not to have a key placed inside this bypass module, we OFFER a KEYLESS INTERFACE
BYPASS MODULE that does not require a key to be placed inside the bypass module,
this is Part # PKALL or PKFM, either one will work, to order, go to the INTERFACE
BYPASS MODULE PAGE on this website.
NOTE #2: the SJB (Smart Junction Box) is part of the FUSE/RELAY BOX under the
DRIVERS SIDE of the DASH.
NOTE #3; On Vehicles with MEMORY SEATS, the POWER LOCK and UNLOCK wires are in
the PASSENGER KICK PANEL or SJB (Smart Junction Box) and you will need to
TEST these wires while using the LOCK/UNLOCK Switch on the Passenger Door only.
NOTE #4; the DOMELIGHT SUPERVISION wire BLUE (+) can also be located in the
PASSENGER side "A" Pillar.
NOTE #5; Test this wire will turning the Key in the Drivers Door Key Cylinder.
|
|
|
|
|
|
