Vehicle
Wiring Details for your
2006-2008 Pontiac Solstice Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2006-2008 Pontiac Solstice . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
RED/BLACK (+) (10 Gauge) |
@ BCM, C3, Pin D1, See NOTE #2 |
| STARTER |
See NOTE #1 |
|
| STARTER
2 |
N/A |
|
| IGNITION
1 |
YELLOW (+) (20 Gauge) |
@ IGNITION HARNESS or BCM, C4, Pin D3, See NOTE #2 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
BROWN (+) (12 Gauge) |
@ BCM, C4, C8, See NOTE #2 |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BROWN/WHITE (-) |
@ HEADLIGHT SWITCH or BCM, Connector C2, Pin 5, See NOTE #2 |
| PARKING
LIGHTS ( + ) |
BROWN (+) |
IN DRIVERS KICK PANEL or BCM, C3, Pin A7 See NOTE #2 |
| POWER LOCK |
Use Motor Wires, GRAY (TYPE C) |
IN DRIVERS KICK PANEL or BCM, C3, Pin A4, See NOTE #2 |
| POWER UNLOCK |
Use Motor Wires, TAN (TYPE C) |
IN DRIVER KICK PANEL or BCM, C3, Pin B1, See NOTE #2 |
| DOOR TRIGGER |
GRAY/BLACK (-) Drivers Door and TAN/WHITE (-) Passenger Door, use both See NOTE #3 |
IN EACH KICK PANEL or BCM, C1, Pins 22 and 19, See NOTE #2 |
| DOMELIGHT
SUPERVISION |
GRAY (-) |
@ BCM, C3, Pin A10, See NOTE #2 |
| TRUNK RELEASE |
TAN (-) |
@ RELEASE SWITCH or BCM C2 PIN 10, GRAY Plug, See NOTE #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
TAN (-) |
@ HORN SWITCH or BCM, C2, Pin 14, See NOTE #2 |
| TACH |
ANY wire NOT PINK/BLACK (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
LIGHT BLUE (+) |
IN PASSENGER KICK PANEL or BCM, C1, Pin 53, See NOTE #2 |
| FACTORY
ALARM DISARM |
DISARMS with FACTORY REMOTE ONLY!!! |
|
| ANTI-THEFT |
PONTIAC'S MULTIPLEX IGNITION/TRANSPONDER SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: THIS VEHICLE REQUIRES A SPECIAL INTERFACE BYPASS MODULE TO REMOTE START PART # DB-ALL FOR THE 2006 AND PART # DB-ALL or XK09 FOR THE 2007-2008, THESE MODULES WILL ALSO DO THE KEYLESS ENTRY WITH ON EXTRA PARTS NEEDED, TO ORDER PLEASE GO TO THE INTERFACE BYPASS MODULE PAGE ON THIS WEBSITE.
NOTE #2: the BCM (Body Control Module) is part of the FUSE/RELAY BOX below the GLOVE BOX, the BCM will have these connectors: C1 a 72-Pin GRAY Plug, C2 a 72-Pin GRAY Plug, C3 a 41-Pin RED Plug, and C4 a 68-Pin LIGHT GRAY Plug located on the BACK of the BCM.
NOTE #3: When connecting to an Alarm System, use both wires and DIODE ISOLATE, See DIAGRAM
|
|
|
|
|
|
