Vehicle
Wiring Details for your
2006 -2008 Cadillac Dts Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2006 -2008 Cadillac Dts . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
Connect to BATTERY ONLY |
|
| STARTER |
YELLOW (Not for Remote Starting) |
@ ECM, BLUE Plug, Pin 26, See NOTE *1 |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
PINK (+) |
@ IGNITION SWITCH HARNESS or BCM, Connector C1, Pin 14, See NOTE *2 |
| IGNITION
2 |
See NOTE *3 |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
BROWN (+) |
@ IGNITION SWITCH HARNESS or BCM, Connector C1, Pin 21, See NOTE *2 |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
LIGHT BLUE (-) |
@ HEADLIGHT SWITCH or BCM, Connector C2, Pin 8, See NOTE *1 |
| PARKING
LIGHTS ( + ) |
PURPLE (+) LEFT and BROWN/WHITE (+) RIGHT, USE BOTH wires, will require (2) extra Relays, See DIAGRAM |
IN PASSENGER KICK PANEL, Harness to REAR of vehicle. |
| POWER LOCK |
See NOTE * 5 |
|
| POWER UNLOCK |
See NOTE * 5 |
|
| DOOR TRIGGER |
See NOTE *4 |
|
| DOMELIGHT
SUPERVISION |
GRAY/BLACK (+), Requires #R30-H Relay |
IN PASSENGER KICK PANEL or BCM, Connector C6, Pin 1, See NOTE *1 |
| TRUNK RELEASE |
LIGHT BLUE (-) , Requires #R30-H Relay |
@ TRUNK RELEASE SWITCH or BCM, Connector C2, Pin 10, See NOTE *1 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
YELLOW to TAN (-) |
@ HORN SWITCH or BCM, BROWN Plug, Pin 18, See NOTE *1 |
| TACH |
NOT PINK/GRAY or PINK/BLACK |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
LIGHT BLUE (+) or YELLOW/WHITE (+) |
IN PASSENGER KICK PANEL or BCM, BROWN Plug, Pin 5, See NOTE *1 |
| FACTORY
ALARM DISARM |
LIGHT GREEN (-) test while turning the Key in the Drivers Door |
@ DRIVERS DOOR MODULE in DRIVERS DOOR, BROWN Plug |
| ANTI-THEFT |
GM's PASSKEY 3 (PK3 on Steel Shaft of Ignition Key) TRANSPONDER SYSTEM |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE *1 the ECM (Engine Control Module) is in the DRIVERS SIDE of the ENGINE Compartment, in the Air Cleaner Assembly.
NOTE *2 the BCM (Body Control Module) is located behind the Glove Box and to the RIGHT.
NOTE *3 There is a WHITE wire and a WHITE/BLACK wire in the IGNITION HARNESS or the BCM, C1, Pins 2 and 4 that work as the Starter, and Second Ignition, at this time there is no information on if these wires will need to be wired in for the New Passlock system as needed on the Chevy Cobalt. check back for more information in the near future!!!
NOTE *4 The DRIVERS DOOR is a GRAY/BLACK (-) at the DRIVERS DOOR MODULE in the DRIVERS DOOR, BROWN Plug, the PASSENGER DOOR is a TAN/WHITE (-) at the PASSENGER DOOR MODULE, in the PASSENGER DOOR, BROWN Plug, the DRIVERS REAR DOOR is a BLUE/BLACK (-) at the BCM, C6, Pin 15 and the PASSENGER REAR DOOR is a LIGHT GREEN/BLACK (-) at the BCM, C6, Pin 14, when connecting to an Alarm System, use all (4) wires and Diode Isolate.
NOTE *5 This vehicle uses a multi-plex doorlocking system that requires a bypass. The model XK01 with GMDL6X 4.00 firmware will operate the doorlocks.
|
|
|
|
|
|
