Vehicle
Wiring Details for your
2006-2007 Mercury Mountaineer Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2006-2007 Mercury Mountaineer . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
PURPLE/RED (+) |
@ IGNITION SWITCH HARNESS |
| STARTER |
BLUE/WHITE (+) |
@ IGNITION SWITCH HARNESS |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
WHITE/ORANGE (+) |
@ IGNITION SWITCH HARNESS |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
PURPLE/GREEN (+) |
@ IGNITION SWITCH HARNESS |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
GRAY (-) |
@ HEADLIGHT SWITCH or SJB, Connector D, Pin 3, See NOTE #2 |
| PARKING
LIGHTS ( + ) |
BLUE/WHITE (+) |
IN DRIVERS KICK PANEL or SJB, Connector A, Pin 11, See NOTE #2 |
| POWER LOCK |
GRAY/YELLOW (TYPE B) |
IN DRIVER KICK PANEL or SJB, Connector B, Pin 27, See NOTE #2 |
| POWER UNLOCK |
PURPLE/GRAY (TYPE B) |
IN DRIVERS KICK PANEL or SJB, Connector B, Pin 26 See NOTE #2 |
| DOOR TRIGGER |
Use DOME LIGHT SUPERVISION wire |
|
| DOMELIGHT
SUPERVISION |
YELLOW/GRAY (+) |
IN DRIVERS KICK PANEL or SJB, Connector A, Pin 8, See NOTE #2 |
| TRUNK RELEASE |
BROWN (-) |
IN DRIVERS KICK PANEL or SJB, Connector B, Pin 29, See NOTE #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
BLUE/WHITE (-) |
@ HORN SWITCH or SJB, Connector C, Pin 6, See NOTE #2 |
| TACH |
Any wire NOT GRAY or PURPLE (AC) |
@ Any FUEL-INJECTOR or IGNITION COIL |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
PURPLE/WHITE (+) |
@ SWITCH above BRAKE PEDAL or SJB, Connector A, Pin 15, See NOTE #2 |
| FACTORY
ALARM DISARM |
N/A |
|
| ANTI-THEFT |
FORD'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is equipped with a Special Anti-theft key, to remote start you will
need a Bypass module 791, use this module IF you have a extra ignition key to
place inside the 791 to remote start, if you do not have an extra key to use or wish
not to have a key placed inside this bypass module, we OFFER a KEYLESS INTERFACE
BYPASS MODULE that does not require a key to be placed inside the bypass module,
this is Part # PKALL or PKFM, either one will work, to order, go to the INTERFACE
BYPASS MODULE PAGE on this website.
NOTE #2; the SJB (Smart Junction Box) is part of the FUSE/RELAY BOX under the DRIVERS
SIDE of the DASH.
|
|
|
|
|
|
