Vehicle
Wiring Details for your
2006-2007 Isuzu I-350 Wiring Diagram |
Printer Friendly Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2006-2007 Isuzu I-350 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
|
PART |
COLOR |
LOCATION |
12 VOLT
CONSTANT |
Connect DIRECTLY to BATTERY!! |
|
STARTER |
YELLOW/BLACK (-), (NOT for REMOTE STARTING!!), NOTE #1 |
@ PCM, (BLUE PLUG), PIN 48, NOTE #3 |
STARTER
2 |
WHITE/BLUE to WHITE, (MUX), NOTE #1 |
@ IGNITION SWITCH, (PIN 4) or BCM, (GRAY PLUG), PIN A14, NOTE #2 |
IGNITION
1 |
WHITE/GREEN to DK. BLUE (+), NOTE #1 |
@ IGNITION SWITCH, (PIN 3) or BCM, (GRAY PLUG), PIN B8, NOTE #2 |
IGNITION
2 |
N/A |
|
IGNITION
3 |
N/A |
|
ACCESSORY/HEATER
BLOWER 1 |
WHITE/RED to BROWN (+), NOTE #1 |
@ IGNITION SWITCH, (PIN 1) or BCM, (GRAY PLUG), PIN B7, NOTE #2 |
ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
KEYSENSE |
N/A |
|
PARKING
LIGHTS ( - ) |
BROWN/WHITE (-) |
@ HEADLIGHT SWITCH or BCM, (GRAY PLUG), PIN A7, NOTE #2 |
PARKING
LIGHTS ( + ) |
BROWN (+) |
@ BCM, (BLACK PLUG), PIN A48, NOTE #2 |
POWER LOCK |
LT. BLUE (-), TYPE B |
in EITHER KICK PANEL or BCM, (BLACK PLUG), PIN A11, NOTE #2 |
POWER UNLOCK |
DK. BLUE (-), TYPE B, NOTE #4 |
in EITHER KICK PANEL at DOOR HARNESS |
DOOR TRIGGER |
NOTE #5 |
@ BCM, (BLACK PLUG), NOTE #2 |
DOMELIGHT
SUPERVISION |
WHITE (-) |
@ BCM, (BLACK PLUG), PIN A46, NOTE #2 |
TRUNK RELEASE |
N/A |
|
SLIDING
POWER DOOR |
N/A |
|
HORN |
GREEN to BLACK (-) |
@ HORN SWITCH or BCM, (GRAY PLUG), PIN A25, NOTE #2 |
TACH |
Any wire NOT PINK or BLACK, (AC) |
@ Any IGNITION COIL or FUEL-INJECTOR |
WAIT TO
START LIGHT |
N/A |
|
BRAKE |
LT. BLUE (+) |
@ BRAKE PEDAL SWITCH |
FACTORY
ALARM DISARM |
DISARMS with FACTORY REMOTE ONLY!! |
|
ANTI-THEFT |
GM'S (ION TYPE) PASSLOCK 2 ANTI-THEFT SYSTEM, Requires Bypass Module, See NOTE #1 |
@ IGNITION SWITCH HARNESS |
EXTRA
INFORMATION |
NOTE #1: REQUIES SPECIAL BYPASS MODULE for REMOTE STARTING: Use a PLXR, PLJX, or an XK06 with PLXR 3.00 firmware. If you use a CANMAX 400 with 400.GM5 0.13 firmware, this will, in addition to remote start, also operate door locks and factory alarm.
NOTE #2: the BCM (Body Control Module) is located in the PASSENGER KICK PANEL.
NOTE #3: the PCM, (Powertrain Control Module) is located in the PASSENGER KICK PANEL.
NOTE #4: to UNLOCK just the DRIVERS DOOR, use the WHITE (-) at the BCM, (BLACK PUG), PIN A12.
NOTE #5: This vehicle has (4) DOOR TRIGGER wires the GRAY/BLACK (-) is used for the DRIVERS DOOR, Pin A32, the PASSENGER DOOR is a LIGHT GREEN/BLACK (-) Pin A38, the DRIVERS REAR DOOR is a LIGHT BLUE/BLACK (-) Pin A44 and the PASSENGERS REAR DOOR is a BLACK/WHITE (-) Pin A39 all are located at the BCM's BLACK Plug. When connecting to an ALARM SYSTEM use all 4 DOOR TRIGGER wires and DIODE ISOLATE.
|
|
|
|
|