Vehicle
Wiring Details for your
2005-2007 Mercury Mariner Wiring Diagram |
Printer Friendly Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2005-2007 Mercury Mariner . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
|
PART |
COLOR |
LOCATION |
12 VOLT
CONSTANT |
Connect to BATTERY ONLY |
@ IGNITION SWITCH HARNESS |
STARTER |
TAN/LIGHT BLUE (+) |
@ IGNITION SWITCH HARNESS |
STARTER
2 |
N/A |
|
IGNITION
1 |
LIGHT GREEN/PURPLE (+) |
@ IGNITION SWITCH HARNESS |
IGNITION
2 |
N/A |
|
IGNITION
3 |
N/A |
|
ACCESSORY/HEATER
BLOWER 1 |
BLACK/LIGHT GREEN (+) |
@ IGNITION SWITCH HARNESS |
ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
KEYSENSE |
N/A |
|
PARKING
LIGHTS ( - ) |
WHITE/BLACK (-) |
@ SJB, Connector E, Pin 4, See NOTE #2 |
PARKING
LIGHTS ( + ) |
BROWN (+) |
@ SJB, Connector C, Pin 19, See NOTE #2 |
POWER LOCK |
PINK/WHITE (1-Wire Door Lock System), See NOTE #3 |
@ SJB, Connector B, Pin 22, See NOTE #2 |
POWER UNLOCK |
Same wire, See DIAGRAM |
See DAIGRAMS |
DOOR TRIGGER |
PINK (-) |
@ SJB, Connector C, Pin 28, See NOTE #2 |
DOMELIGHT
SUPERVISION |
USE DOOR TRIGGER, (Requires # 775 relay) |
|
TRUNK RELEASE |
N/A |
|
SLIDING
POWER DOOR |
N/A |
|
HORN |
YELLOW/LIGHT GREEN (-) |
@ SJB, Connector A, Pin 14, See NOTE #2 |
TACH |
Any wire that is NOT RED or WHITE/RED (AC) |
@ IGNITION COIL or FUEL INJECTOR |
WAIT TO
START LIGHT |
N/A |
|
BRAKE |
LIGHT GREEN (+) |
@ SJB, Connector C, Pin 14, See NOTE #2 |
FACTORY
ALARM DISARM |
DARK BLUE/LIGHT GREEN (-) |
@ SJB, Connector D, Pin 3, See NOTE #2 |
ANTI-THEFT |
FORD'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
EXTRA
INFORMATION |
NOTE #1: This vehicle is equipped with a Special Anti-theft key, to remote start you will
need a Bypass module 791, use this module IF you have a extra ignition key to
place inside the 791 to remote start, if you do not have an extra key to use or wish
not to have a key placed inside this bypass module, we OFFER a KEYLESS INTERFACE
BYPASS MODULE that does not require a key to be placed inside the bypass module,
this is Part # PKALL or PKFM, either one will work, to order, go to the INTERFACE
BYPASS MODULE PAGE on this website.
NOTE #2: the SJB (Smart Junction Block) is the FUSE/RELAY Box on the Passenger side of
the Center Console.
NOTE #3: this vehicle uses a 1-Wire Door Locking System, a (-)Negative thru a 1000 Ohm
Resistor, LOCKS and a Straight (-)Negative UNLOCKS, some units also require 2
extra relays Part #775 for this circuit, to connect, See DIAGRAMS
|
|
|
|
|