PART	COLOR	LOCATION
12 VOLT CONSTANT	RED/WHITE (+)	IGNITION SWITCH HARNESS
STARTER	YELLOW (-) (NOT REQUIRED FOR REMOTE STARTING) See NOTE *3	@ PCM, BLUE Plug Pin 23, See NOTE *6
STARTER 2	N/A
IGNITION 1	PINK (+) Needs Part #R30-H Relay See DIAGRAM	IGNITION SWITCH HARNESS, See DIAGRAM
IGNITION 2	N/A
IGNITION 3	N/A
ACCESSORY/HEATER BLOWER 1	ORANGE (+) See NOTE *4, See DIAGRAM	IGNITION SWITCH HARNESS, See DIAGRAM
ACCESSORY/HEATER BLOWER 2	N/A
KEYSENSE	LIGHT GREEN (-) (Required for Remote Starting See NOTE *7)	@ BCM, GRAY 24-Pin Plug, Pin A8 See NOTE *5
PARKING LIGHTS ( - )	LIGHT BLUE (-)	@ BCM, GRAY Plug,Pin B6, NOTE *5
PARKING LIGHTS ( + )	BROWN (+)	@ BCM, GRAY Plug, Pin B10, NOTE *5
POWER LOCK	LIGHT BLUE (Positive (+))	@ BCM, PINK plug, Pin B4, NOTE *5
POWER UNLOCK	DARK BLUE (Positive (+))	@ BCM, GRAY plug, Pin A3, NOTE *5
DOOR TRIGGER	GRAY/BLACK (-) and TAN/WHITE (-) Use both wires, See NOTE *1
DOMELIGHT SUPERVISION	WHITE (-)	@ BCM, PINK Plug, Pin A1, See NOTE *5
TRUNK RELEASE	N/A
SLIDING POWER DOOR	N/A
HORN	TAN (-)	@ BCM, PINK plug, Pin A3, See NOTE *5
TACH	PURPLE, See NOTE *2	@ IGNITION CONTROL MODULE
WAIT TO START LIGHT
BRAKE	LIGHT BLUE (+)	@ SWITCH ABOVE BRAKE PEDAL
FACTORY ALARM DISARM	DISARMS with FACTORY REMOTE ONLY!!!
ANTI-THEFT	YELLOW and ORANGE/BLACK	GM's PASSLOCK 2 System, wires are in Ignition Switch Harness

EXTRA INFORMATION

NOTE *1 The GRAY/BLACK (-) is for the DRIVERS DOOR and is located at the BCM, PINK Plug, Pin B8, the PASSENGER DOOR is a TAN/WHITE (-) at the BCM, GREY Plug, Pin B5, WHEN CONNECTING TO AN ALARM SYSTEM use both wires and DIODE ISOLATE. See DIAGRAM NOTE *2 The IGNITION CONTROL MODULE is located on TOP and to the REAR of the ENGINE. NOTE *3 This vehicle for REMOTE STARTING DOES NOT REQUIRE the connection to the STARTER/CRANK wire, the vehicle will Crank when it see power to the IGNITION and then the droping out of voltage on the ACCESSORY wire will automaticlly start the vehicle. The installation of the 791 Bypass Module DOES require a connection to the STARTER CRANK wire, to make the 791 work you will need to do this. Take the YELLOW/BLACK from the 791 and apply it to 12 volts constant while cranking the vehicle with the ignition key, after the vehicle starts, take the YELOW/BLACK wire from the 791 off of the 12 volts constant. in 10 to 20 seconds the RED light in the 791 will turn off. Repeat this step 2 more times, the RED light in the 791 will turn on and then off each time, turn the vehicle off and then tape the YELLOW/BLACK wire from the 791 up and do not use. NOTE *4 if the Remote Starter Module DOES NOT DROP the voltage out to the ACCESSORY wire during cranking it will be necessary to add a Relay Part #R30-H, See DIAGRAM NOTE *5 the BCM is located in the CENTER CONSOLE, below the RADIO. NOTE *6 the PCM is located in FRONT of the DRIVERS STRUT TOWER, above the BATTERY COVER. NOTE *7 this Key Sense wire is ONLY needed if the CHECK ENGINE light turns ON during remote starting.