Vehicle
Wiring Details for your
2005 -2007 Chevrolet Corvette Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2005 -2007 Chevrolet Corvette . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
RED/BLACK (+) |
@ BCM, C3, Pin D1, See NOTE *1 |
| STARTER |
PURPLE (+) Not Required for Remote Start |
@ STARTER or FUSE BLOCK UNDER HOOD |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
PINK (+) Not Required for Remote Start |
@ BCM, C4, Pin C8, See NOTE *1 |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BROWN/WHITE (-) |
@ BCM, Plug C2, Pin 5, See NOTE *1 |
| PARKING
LIGHTS ( + ) |
BROWN (+) |
@ HARNESS going to REAR of vehicle |
| POWER LOCK |
ORANGE/BLACK (Negative (-)) |
@ LOCK SWITCH in DRIVERS Door |
| POWER UNLOCK |
ORANGE/BLACK (Negative (-)) |
@ LOCK SWITCH in DRIVERS Door |
| DOOR TRIGGER |
GRAY/BLACK (-) and TAN/WHITE (-) Use both, See NOTE *2 |
@ BCM, C1, Pins 51 and 53, See NOTE *1 |
| DOMELIGHT
SUPERVISION |
WHITE (-) |
@ BCM, C3, Pin A10, See NOTE *1 |
| TRUNK RELEASE |
BROWN/WHITE (-) |
@ BCM, C1, Pin 71, See NOTE *1 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
YELLOW to TAN (-) |
@ BCM, C2, Pin 14, See NOTE *1 |
| TACH |
WHITE |
@ ECM, BLUE Plug Pin 48, See NOTE *3 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
LIGHT BLUE (+) |
@ BCM, C4, Pin D4, See NOTE *1 |
| FACTORY
ALARM DISARM |
DISARMS with FACTORY REMOTE ONLY!!! |
|
| ANTI-THEFT |
NO INFORMATION AT THIS TIME! |
|
| EXTRA
INFORMATION |
| NOTE *1 the BCM is part of the FUSE/RELAY BLOCK on the Passenger floor board under the carpet. The BCM has these connectors: C1 is a GRAY 72-Pin, C2 is a GRAY 72-Pin, C3 is a RED 42-Pin, and C4 is a GRAY 68-Pin Connector.
NOTE *2 this vehicle has 2 (-) door pin trigger wires, when connecting to an ALARM SYSTEM, you will need to use both and DIODE ISOLATE, See DIAGRAM
NOTE *3 the ECM is located in the FRONT PASSENGER FENDER, remove the wheel to access the panel located behind the wheel. The access panel will let you get to the ECM.
NOTE *4 these wirs can also be found at the KEYLESS ENTRY MODULE, located under the UPPER DASH PANEL towards the passenger side.
|
|
|
|
|
|
