Vehicle
Wiring Details for your
2005 - Toyota Celica Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2005 - Toyota Celica . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
WHITE (+) |
IGNITION SWITCH HARNESS |
| STARTER |
BLACK/WHITE (+) |
IGNITION SWITCH HARNESS |
| STARTER
2 |
N/A |
|
| IGNITION
1 |
BLACK/ORANGE (+) See NOTE *1 |
IGNITION SWITCH HARNESS, See DIAGRAM |
| IGNITION
2 |
BLUE/RED (+) See NOTE *2 |
IGNITION SWITCH HARNESS |
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
GRAY (+) |
IGNITION SWITCH HARNESS |
| ACCESSORY/HEATER
BLOWER 2 |
N/A |
|
| KEYSENSE |
YELLOW (-) |
IGNITION SWITCH HARNESS or BECU, TOP PLUG, PIN 9, See NOTE *3 |
| PARKING
LIGHTS ( - ) |
LIGHT GREEN (-) |
@ HEADLIGHT SWITCH or BECU, TOP Plug, Pin 5, See NOTE *3 |
| PARKING
LIGHTS ( + ) |
GREEN (+) |
@ BACK of FUSEBOX, 13-PIN PLUG |
| POWER LOCK |
BROWN (Negative (-)) See NOTE *4 |
IN DRIVERS KICK PANEL or 20-PIN PLUG, BACK OF FUSE BOX |
| POWER UNLOCK |
YELLOW/BLACK (Negative (-)) (Requires Double Pulse) See NOTE *4 |
IN DRIVERS KICK PANEL or BECU, TOP PLUG, PIN 25 |
| DOOR TRIGGER |
RED/YELLOW (-) and RED (-) Use both, See NOTE *5 |
@ BECU, BOTTOM PLUG, PINS 20 and 21, See NOTE *1 |
| DOMELIGHT
SUPERVISION |
RED/WHITE (-), Requires Part #R30-H Relay |
IN DRIVERS KICK PANEL or BECU, TOP PLUG, PIN 10, See NOTE *3 |
| TRUNK RELEASE |
N/A |
|
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
BLUE/BLACK (-) |
@ BECU, TOP PLUG, PIN 14, See NOTE *3 |
| TACH |
BROWN/WHITE |
@ BACK of FUSEBOX, 20-PIN PLUG, PIN 4 |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
GREEN/WHITE (+) |
@ BACK of FUSEBOX, 13-PIN PLUG |
| FACTORY
ALARM DISARM |
DISARMS with KEYSENSE wire |
|
| ANTI-THEFT |
N/A |
|
| EXTRA
INFORMATION |
| NOTE *1 this vehicle will require an extra relay Part #R30-H to isolate the IGNITION #2 wire, to connect, See DIAGRAM
NOTE *2 THERE ARE 2 BLUE/RED (+) WIRES IN THE IGNITION HARNESS. THE CORRECT IGNITION WIRE IS THE HEAVIER GUAGE WIRE AND IT HAS (1) SILVER HASH MARK .THE WRONG WIRE HAS 2 SILVER HASH MARKS.
NOTE *3 the BECU (Body Electronic Control Unit) is attached to the back of the FUSEBOX, you must remove the RADIO to access.
NOTE *4 the LOCK and UNLOCK wires will only TEST while turning the key in the DRIVERS DOOR KEY CYLINDER.
NOTE *5 the DRIVERS DOOR is a RED/YELLOW(-) and the PASSENGER DOOR is a RED(-) when connecting to an ALARM System, use both DOOR TRIGGER wires and DIODE ISOLATE, to connect, See DIAGRAM.
|
|
|
|
|
|
