Item |
Wire Color |
Polarity |
Wire
Location |
12V |
red/white |
Positive (+) |
ignition harness |
Starter |
yellow |
Positive (+) |
ignition harness |
Starter 2 |
none |
|
|
Ignition |
dk. blue/gray |
Positive (+) |
ignition harness |
2nd Ignition |
none |
|
|
3rd Ignition |
none |
|
|
Accessory |
blk/org [1] |
Positive (+) |
ignition harness |
Accessory
2 |
red/blk [1] |
Positive (+) |
ignition harness |
Tachometer |
gray/white |
|
PCM [5] |
Power Door
(Lock)
Wiring
Diagram for
[5 Wire]
Door Lock |
org/pur - blk/wht |
5 Wire |
[2] |
Power Door (Unlock)
Wiring
Diagram for
[5 Wire]
Door Unlock |
pnk/blk - pnk/blk |
5 Wire |
[2] |
Door Trigger |
yellow [3] |
Negative (-) |
drivers kick panel |
Dome Supervision
Wiring
Diagram for
[none]
Dome |
none |
none |
none |
Headlights |
tan/black |
Positive (+) |
at light switch |
Parklight Positive |
dk. blue/red |
Positive (+) |
at light switch |
Parklight Negative |
none |
|
|
Wipers |
brn/wht & red/yel |
Positive (+) |
wiper switch |
Left Front Window
(Up/Down) |
lt blue - white |
|
in drivers door |
Right Front Window
(Up/Down) |
brown - purple |
|
in passengers door |
Left Rear Window
(Up/Down) |
dk grn/wht - gry/blk |
B |
drivers kick [6] |
Right Rear Window
(Up/Down) |
gry/blk - dk grn/wht |
B |
passenger kick [6] |
Trunk/Hatch Pin |
tan/black |
Negative (-) |
left of column [3] |
Hood Pin |
brown/tan |
Negative (-) |
drivers kick panel |
Trunk/Hatch Release
Wiring
Diagram for
[Positive (+)]
Trunk/Hatch |
orange/brown |
Positive (+) |
release switch |
Factory Alarm
(Arm) |
none |
|
|
Factory Alarm
(Disarm) |
purple/yellow |
Negative (-) |
door harness DKP [4] |
Horn |
gray/orange |
Negative (-) |
steering column |
Brake |
white/tan |
Positive (+) |
at brake pedal switch |
Door Motor
(Lock) |
none |
none |
none |
Door Motor
(Unlock) |
none |
none |
none |
Disarm |
none |
none |
none |
Disarm No Unlock |
none |
none |
none |
 |
Additional
Info: |
Note : Use Commando part number JDL door lock control module.This will control door lock, unlock, arm, disarm, dome light supervision and more. [1] Both wires must be powered for remote start. [2] Use orange/purple for lock and pink/black for unlock at the drivers door switch to operate the drivers door lock. Use black/white for lock and pink/black for unlock at the passenger front door switch to unlock all passenger doors. It is required to interface in each door even if the vehicle is equiped with keyless entry. [3] To avoid dome light delay there are 5 separate trigger wires in a 14 pin black plug at the BCM located between the steering column and the drivers kick panel. The plug is located in the drivers side front corner of BCM just behind the knee bolster. All wires in the plug exit straight down. The door trigger colors are tan, tan/red, tan/orange, and tan/yellow. The trunk trigger color is tan/black. All of them are negative trigger. Grab each wire and diode isolate. WHEN USING A JDL INTERFACE MODULE, IT IS NOT NECESSARY TO USE THE SEPARATE TRIGGER WIRES. [4] Also located in the same 14 pin black connector as the separate door trigger wires. See above notes for exact location. [5] The PCM is located high on the passenger side firewall. [6] When using a JDL it is required to go into each rear door and use brown for up and purple for down. |
|
 |
ATTENTION:
This wiring information is being provided free of charge and on
an "as is" basis, without any representation or
warranty. It is your responsibility to verify any circuit before
interfacing with it by using a digital multimeter. GNU Industries,
Inc. assumes no responsibility with regards to the accuracy or currency
of this information. Proper installation in every case is and remains
the responsibility of the installer. GNU assumes no responsibility
resulting from an improper installation, even in reliance upon this
information.
Copyright ©
2000-2006 GNU Industries, Inc. All Rights Reserved. |
|