Vehicle
Wiring Details for your
2004- Dodge Intrepid Wiring Diagram |
Printer Friendly Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2004- Dodge Intrepid . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
|
PART |
COLOR |
LOCATION |
12 VOLT
CONSTANT |
PINK/BLACK (+) and RED (+) |
@ IGNITION SWITCH HARNESS |
STARTER |
YELLOW (+) |
@ IGNITION SWITCH HARNESS |
STARTER
2 |
N/A |
|
IGNITION
1 |
DARK BLUE/WHITE (+) |
@ IGNITION SWITCH HARNESS |
IGNITION
2 |
DARK GREEN/RED (+) |
@ IGNITION SWITCH HARNESS |
IGNITION
3 |
N/A |
|
ACCESSORY/HEATER
BLOWER 1 |
BLACK/ORANGE (+) |
@ IGNITION SWITCH HARNESS |
ACCESSORY/HEATER
BLOWER 2 |
BLACK/WHITE (+) |
@ IGNITION SWITCH HARNESS |
KEYSENSE |
N/A |
|
PARKING
LIGHTS ( - ) |
YELLOW (-), See NOTE #2 |
@ HEADLIGHT SWITCH or BCM, BLACK Plug, Pin 2, See NOTE #5 |
PARKING
LIGHTS ( + ) |
BLACK/YELLOW (+) |
@ BACK of JUNCTION BLOCK, GRAY Plug, Pin 11 |
POWER LOCK |
WHITE/DARK GREEN (1-Wire Door Lock System), See NOTE #3 |
@ BCM, BLUE Plug, Pin 5, See DIAGRAM |
POWER UNLOCK |
Same wire, See DIAGRAM |
See DIAGRAMS |
DOOR TRIGGER |
See NOTE #4 |
@ BCM, See NOTE #5 |
DOMELIGHT
SUPERVISION |
YELLOW (-), (Requires #775 Relay) |
@ FRONT of JUNCTION BLOCK, TAN Plug, Pin 4 |
TRUNK RELEASE |
BLACK/WHITE (+) |
@ TRUNK RELEASE SWITCH or BCM, GRAY Plug, Pin 1, See NOTE #5 |
SLIDING
POWER DOOR |
N/A |
|
HORN |
BLACK/RED (-) |
@ BACK of JUNCTION BLOCK, GRAY Plug, Pin 6 |
TACH |
ANY wire NOT DARK GREEN/LIGHT GREEN (AC) |
@ ANY COIL or FUEL INJECTOR |
WAIT TO
START LIGHT |
N/A |
|
BRAKE |
WHITE/TAN (+) |
@ SWITCH ABOVE BRAKE PEDAL |
FACTORY
ALARM DISARM |
LIGHT GREEN/ORANGE (-), See NOTE #6 |
@ BCM, BLUE Plug, Pin 13, See NOTE #5 |
ANTI-THEFT |
CHRYSLER'S ANTI-THEFT TRANSPONDER System (GRAY IGNITION KEY), See NOTE #1 |
@ IGNITION SWITCH TUMBLER |
EXTRA
INFORMATION |
NOTE #1: This vehicle may be equipped with CHRYSLER'S ANTI-THEFT TRANSPONDER System
(GRAY IGNITION KEY), if so to remote start will require the 791 BYPASS MODULE and
an extra Ignition key, to order go to the SECURITY BYPASS MODULE PAGE on this
website.
NOTE #2: the PARKING LIGHTS require a (-)Negative thru a 47 Ohm Resistor and an extra
Relay part #775, to connect, See DIAGRAM.
NOTE #3; this vehicle uses a 1-Wire Door Locking System, LOCK requires a (+)Positive thru a
2700 Ohm Resistor and UNLOCK requires a (+)Positive thru a 620 Ohm Resistor,
some units will also require 2 extra relays part #775, to connect, See DIAGRAM
NOTE #4: the DRIVERS DOOR is a TAN (-) Pin 4, the PASSENGER DOOR is a TAN/RED (-) Pin 2,
the DRIVERS REAR DOOR is a TAN/RED (-) Pin 1 and the PASSENGER REAR DOOR is
a TAN/RED (-) Pin 10, when connecting to an ALARM SYSTME, use ALL 4 DOOR
TRIGGER wires and DIODE ISOLATE, to connect, See DIAGRAM
NOTE #5: the BCM (Body Control Module) is located on the DRIVERS SIDE of the DASH
attached to the FUSE/JUNCTION block.
NOTE #6; this FACTORY DISARM wire will require an extra relay part #775 and a (-)Negative
thru a 680 Ohm Resistor, to connect, See DIAGRAM
|
|
|
|
|